Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
Hi Nordic Support Team,
I am currently working on integrating the MAX30001 ECG/Bio-impedance sensor with the Ezurio nRF54L15U DK (nRF54L series). I am using the nRF Connect...
Hi,
1.I'm attempting to create a GRTC wake-up example, but it's giving an error when running. Could you please help me troubleshoot this issue? 2. The line that caused the...
Hi,
I am using nrf70-wifi-ble-image-transfer-demo to transfer a static image stored in the Flash.
While I am using 5Ghz STA mode UDP Wi-Fi, I notice the image will blinky...
Hi Community I've been trying to read a tag from nRF54L15 board .
When checking the NRF connect SDK NFC examples, It seems the NFC Tag reader example is not supported for...
Hi
I am using NCS 2.8 and running one pair of peripheral and central devices using nRF52832.
At first, the default interval is 50 ms, and I can get the throughput around...
Hi, I'm trying to test Channel Sounding with concurrent measurements using one initiator and two reflectors on nRF54L15 DKs.
From replies in other DevZone threads, it seems...
I currently use NRF5SDK v17 with S112 supporting 0-2 peripherals, ideally using data extension (4.2). No encryption is used and I don't need any 5.0 features. I now wish to...
I plan on using the nPM2100 to power the nRF54L15. I'd like to confirm any recommended practices for using the reset pin of the nPM2100.
nPM2100 PG/RESET to nRF54L15...
Hi, I'm trying to use the nRF COMP peripheral in Zephyr. My application boots and runs normally until I enable the DeviceTree overlay for the COMP. As soon as the overlay...
Hello,
What will happen if I try to change the device's TX power using the vendor-specific command SDC_HCI_OPCODE_CMD_VS_ZEPHYR_WRITE_TX_POWER while LE Power Control feature...
hi,
I use nrf54l15dk with ncs-v3.1.0， the project is based sample "central_hids"；
The purpose is I want to change console uart from "pin1.04/pin1.05<uart20>" to "pin2...
I’m developing a project on the nRF52840 that uses BLE + RTC + an SD card. It’s based on a previous project that only used BLE + RTC, and I’ve added the ability to store data...
I'm trying to use a Power Profiler Kit II with a Mac running Ventura 13.7.8. If I update the Power Profiler App to v4.3.0 or v4.3.1 the PPK II is not detected and this is...
Dear Team,
I am using NRF54L15 DK, where I have UART defined and mapped as following:
uart20_default: uart20_default {
group1 {
psels = <NRF_PSEL(UART_TX, 1 ,...
