Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi.
I'm using nrf52832 with SDK-17, and the ESB example (esb_tx and esb_rx)
I'm not much experience in nrf development recently I have a project related to ESB to transmit...
Hello,
In nRF52832, we use nRF Connect to read the board, save the program data into a hex file, and send the file to other developers. They can use nRF Connect to write...
I am using sniffer v3.1. I have installed the sniffer code on a nRF52840 dongle (PCA100059). When I insert this into the PC with windows 8.1 it appears as "nRF Sniffer for...
Hello,
In our product, the nRF9160 is configured to use LTE CAT-M1 and we are measuring the signal quality thorugh the AT+CESQ command.
After begin registered on the...
Hi: I have write a spi slave, and write a spi master on STM32, It can receive data from STM32,But I have no time to prepare the response data.
as the code below, I can receive...
I checked the SPI communication using the NRF52832 development board.
Based on the firmware of the previously developed NRF52810 product, the SPI operation code is applied...
Would like to interface a SPI ADC – MCP3461 via the nRF52840 serial peripheral interface master with EasyDMA (SPIM). I was not able to find whether or not there is an available...
Hi Everyone,
My issue is mostly stated in the subject, I hope someone can help me recover this DK because as of the moment this is my only way to program/debug out EVT board...
I have nrf52833 as Tx. Ialso have nrf52833+ antenna array as Rx. I want to send CTE data, implement IQ sampling and view AOA for implementing direction finding. Kindly assist...
Hi,
I'm considering shifting to SES (from VS-code) to get debug capabilities.
(Zephyr application developed under NCS tag v1.5.1)
I tried to import my project doing...
Hi
I am developing a Zephyr application on a nRF52840.
Is it possible to runtime change pinmux. Eg. I have set rx/tx for an uart to p1.8, p1.9 and want them to be changed...
Hi nordic,
I want dfu the BL only, how should I pack file? Can show me how to pack instructions of nRF Util, only update bootloader.
Thanks and best regards!
John
Hello,
I am using nrf51822 / SDK v12.3 / SD 130.
I want to change the FW of the sold product to a new FW.
The bootloader address / length of the two are the same,...
