We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
THis may have an obvious answer to an experienced embedded programmer but I do not qualify to be that. So I have a piece of working code that runs on the nRF52840 DK and it...
Can you use/link both nfc T4T and T2T libraries and wrapper/driver source in same application/build?
I don't mean emulating both modes at the same time.
Thanks.
To the kind attention of Nordic support team,
I have been using nRF ble sniffer successfully, it is a great tool. But I have some troubles when it comes to use it for ble...
Hi there!
I am placing variables in the ".non_init" section so that their values are retained across software resets. This works great if I only use an App + Soft Device...
I want to modify the uuid through the serial port. What variables can I use to describe this define? Is there any code for reference ?
#define BLE_UUID_NUS_TX_CHARACTERISTIC...
Hi there
I'm currently using three different target platforms/boards #1 : a Nordic PCA10040 - attached to USB #2 : a UTO-NBL-52A developer board - attached to a J-Link plus...
Provisioner and client (provisionee) roles in the same application.
Hello everyone,
First, I am using SDK 17.02 and BLE Mesh 5.0.
By the moment, I want to integrate...
Hello,
I want to realize the data receiving and sending function,so I adapt the transmitter demo in '\nRF5_SDK_16.0.0_98a08e2\examples\peripheral\radio\',and my code is...
Hi all,
we are trying to connect 20 peripherals to one nRF52840 master (connected to a Laptop running a python app with pc-ble-driver-py) and transmit about 1000 Bytes per...
Hi guys,
I have a custom board containing a Raytac nRf52840 module running the Arduino core. The Arduino core configures the nRf52 to expect a 32K crystal on the xtal input...
Hello
I Just got my first Custom PCB's i dont know how to compile the code into them .Can someone help me . I just get the errror messege when i try to find target :
Failed...
Hello, I am using SDK 16.0 and mesh SDK 4.2.
We successfully implemented remote provisioning capabilities in our devices' firmware. One thing we are noticing though is that...
Hi,
I am using spis example from "SDK v17.0.2" with slight modification in the code as given below
On the Master end CS pin is pulled low and send 1 byte(0x45) only...
Hello,
I'm using nrf52840 with gcc compiler and SDK15.3. For our firmware update procedure, we use two flash storage instances. One for the transmitted new application and...
Nordic：
We need to do a communication certification, we need NORDIC to provide S112V6.1.1 QDID: 125078 certification report certificate。
thinks
jermi.jin
2021.061...
