Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
Hi,
I want to run a CoAP server with Zephyr on a Thingy:91 over NB-IoT. Now I noticed that the Thingy only gets a private IPv4 address (10.x.x.x) from my provider which...
Hi, I am working on my custom made board, and I use P09 and P10 as digital outputs. I am aware I should disable NFC by adding the preprocessor: "CONFIG_NFCT_PINS_AS_GPIOS...
Hi All:
As the topic...........
1.what is the relations between the HID descriptor and data IN/OUT buffer?
2.Is the USB generic HID receiver_Function and tansmit_Function...
When launching the nRF9160, the following error occurred: <inf> at_host: UART check failed: 12. Dropping buffer and retrying.
Under what conditions does this come out? ...
I am trying to add DFU to my project, so I merged in the code from the example in the SDK as follows:
I included the same .c files as the example project
I copied over...
Hi,
I did some measurements today on our I2C bus and see that the GND level is different some times. The most time it is not GND level (about 800mV). I checked cross talk...
Dear
I increated a Generic Level module to main elements which have a Generic ONOFF module on Mesh example Light Switch Server project base on PCA10056 DK board for nrf52840...
Hi I am using the example code here https://github.com/NordicPlayground/nRF52-ADC-examples/tree/master/nrfx_saadc_simple_low_power_app_timer_multichannel_oversample to use...
Hello guys,
Has anybody had the issue opening the new version of nRF Connect for Desktop (v3.6.1) in Windows 10 Pro. I have used an older version of this application and...
I want to build a secure boot loader for my custom board based on the nRF52832.
This post claims to walk through the process of building an example of a secure boot loader...
I'm strugglgin to find any documentation on how to set/request the iDRX paging interval in RRC idle. I have a device which sends an MQTT keepalive message every 3minutes,...
I have run into the issue where the soft device is not being processed when I debug so it throws the assertion failed error. After a lot of searching on the forum I came across...
We are using FDS from SDK 17.2.0 on nRF52832.
It is working so far, we can store and read back data.
When putting battery in and out fast, we get sometimes, but often...
I have the thingy52.py script running on a Raspberry Pi 4, and I can successfully poll the sensors when the Thing52 is awake (recently tapped) but when I try to poll in a...
