Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hi All,
I am developing one project and there we are using ADC (i.e., SAADC in nRF). I have designed the hardware where I am using Capacitor ( C14, 2.2µF) which is connected...
Hi. I have a nRF52840 setup using the PWM driver, and it is outputting a 50Khz pulse 50% duty cycle.
How do I modify the sequence values so that I can modulate this 50Khz...
Dear all,
I would like to implement the IEEE 802.15.4 stack, using the driver inside the SDK for Thread and Zigbee. Unfortunately there aren't any examples ad so everything...
Hi! Please, excuse the probably stupid question but I'm a real newbie. I'm trying to perform a long range coverage test. I got two NRF52840 DK. Got to install both Segger...
Hello all,
I have a question about nRF52832.
What I want to do is increase a number every 20 micro seconds.
In other words, count how much time has passed .
(ex...
I’m developing a wireless sensor based on MINEW nRF52832 modules.
I use SDK 16 and SEGGER embedded studio.
The target is powered by a 3.6V Lithium Thionil battery via...
Hello,
I have been trying to setup timer counter for nrf9160dk using the sample I have attached but for some reason the timer value is always read as 0. Not sure if the...
Hi
We are thinking about migrating a project to the nRF52805. One of our concerns was that the nRF52805 may have no "legacy" UART and only supports the UARTE, which is much...
Hey There,
The problem I have is the following:
I am able to open a Port via Putty and C# Script. I set it up like I found it in the docs. ( https://developer.nordicsemi...
Greetings,
If I send empty line (CR or CRLF) to the modem AT port, modem freezes.
Firmware version: 1.2.1
AT%SHORTSWVER %SHORTSWVER: nrf9160_1.2.1 OK
User application...
Hi,
I have developed succesfully an HTTPs client but I am facing a problem related to a relatively long response from the server when I issue a GET request. After the GET...
Hi,
When I try to update the modem firmware I get this error Errorcode: CouldNotCallFunction (0x9) Lowlever error: Unknown value (ffffff24). See attached picture bellow...
I have a issue with nrf21540 in the Transmit state after the Receive state with using of GPIO for control Transmit / Receive switch.
I'm doing next steps for reproducing...
Hi,
I am trying to use the thingy91 to publish some sensor data to an Azure IoT Hub, I've tried to look at mqtt_simple and modified "asset_tracker" application but I couldn...
