Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
Hi,
I am absolutely new to this DLMS and in the course of exploring some kind of opensource DLMS stack I came across this Gurux and fortunately NORDIC did some kind implementation...
Hi,
I am developing an ESB application with 1 central (nrf52832 DK) and several peripheral. The peripheral are nrf52832 + ICM 20948. Development is done with Segger embedded...
I am trying to setup development environment by following below steps.
The nRF Connect SDK Zephyr repository contains a list of required Python modules. Install these modules...
Hi,
I have bought NRF24LE1 module. Now I want to program the module. So, will anybody please suggest me which programmer should I use to write hex file ? I have mPro programmer...
Hi,
I am currently trying to implement a beacon scanner alongside peripheral mode BLE on an nRF52832. As I am only scanning for beacons, I was hoping I would not need to...
I have been trying to connect to 4G using iBasis and other vendor's SIM card but have not been successful.
I have the nrf9160 DK two years ago and have been sparsely trying...
Hi,
We have 4 NRF52833 DK being used for our development work.
Among that, 3 of them have stopped working and are not powering up.
They power up some times when connected...
Hi,
to develop a device driver in Zephyr for TI DAC80501, a 16-bit DAC, I2C interface,
I have to
1. add the dts child node under the i2c controller node
$i2c1...
I'm using the asset tracker project and I want to add in the ability to store information on the board. However when you include the littlefs file system you get a build error...
Hi Team,
We are using the nRF52840 board for our development purpose. We are using the external debugger(i-jet) for our development purpose.
We are able to connect the...
I have a firmware build that uses the nRF52832 (SoftDevice S132) to return a variety of read characteristics to an external device. So far so good. I can verify that the values...
hi ,
i want to use the pin p0.19， p0.20， p0.21， p0.20 as the spi‘s pin scl，cs,mosi,miso.
and i test in the project nRF5_SDK_16.0.0_98a08e2\examples\peripheral\spi
my...
hello,
I have a problem when using the example twi_sensor with nrf52832( nRF5_SDK_15.3.0_59ac345\examples\peripheral\twi_sensor\pca10040\blank\arm5_no_packs)
This example...
Hello,
I'm porting a code from NRF Connect 1.1 to 1.3. Previously I was able to show in the console floats or double values, but now this seems not be possible anymore....
On SDK16.0.0 + Mesh SDK 4.1.0
I am trying to store some user data using the Flash Manager. I am modifying the light switch server mesh example.
There are a lot of posts...
