I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
I am using the ble_app_uart example and I am having a hard time finding the function that writes a UART message to BLE from the Nordic to the host. uart_event_handle() seems...
Hello All,
I am working on nRF51822 use SDK nRF5 12.3.0 version in IAR workbench.
I am write data in the flash so for that i follow below steps,
Step 1: press button...
So, I need to send and receive a data frame with 39 Bytes with a system Dongle-Arduino(with a nRF24L01 module).
My problem is, I tried to configure Dongle to communicate...
Hi,
I cannot update the firmware on the nrf9160 MLM1 Preview development kit we have. Is this possible? or is the devkit voided for the latest nrf connect and nrfjprog...
Good afternoon everyone,
I'm trying to make a working application for the BLE NUS example but with the support of FreeRTOS that is MANDATORY. I work with KEIL. I started...
with NCS v1.3.0 is there a way to turn off partition manager? I want to be able to build my app and mcuboot separately and not use partition manager at all.
Is it possibe to upgrade nRF52-DK on board programmer to program nRF52840? I already have this nRF52DK but in final I found that 52840 will be better choise for my proyect...
Hi, I am reading the datasheet of both the sensor. but i2c register are different.
I am currently work on vl53l1x. please give me the response as early as possible. thanks...
Using SDK 16.0.0 on an nRF 52840 board.
Managed to get a board into a state where it had only data pages and no swap pages, and therefore fds_init fails with the NO_SWAP...
I want to use nrf SPI driver for SPI flash implementation. For that want to send either SPI transmit or SPI receive at single instance to write or read flash address. But...
Version: Mac OS X 10.15.5 (19F101)
I'm using the nRF Connect app Getting Started Assistant and manage to get through most of it. However, when I use Segger to open up a...
Im trying to run http_client example in zephyr folder (ncs\v1.3.0\zephyr\samples\net\sockets\http_client). When i debug, the app run to fault, i dont know what fault but it...
Hello,
I am trying to use lua script language on nrf52840 board using SES to compile and load code.
I already compiled and load some ble tutorials on nrf52840 and it...
Hi,
I'm trying to use the CryptoCell-312. As I've seen until now, it is not supported by Nrf Connect SDK. Is there a way to use CryptoCell-312? Is it possible to access...
I am using nRF52840 with SDK16 building with armgcc and trying to intergrate buttonless OTA into my project.
App details:
Based on the ble_app_hrs_freertos example project...
