Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
I'm very new and trying to get the nRF Blinky example to work with an iPhone with an nRF52840.
I'm able to connect to the device and it seems to be reading and writing correctly...
I am using S130, SDK13 and NRF52832 both on my central and peripheral - custom boards.
I am trying to avoid service discovery on my peripheral.
I have set the service_changed...
Hi, Does anyone know how to modify the asset tracker so that rather than point to the AWS URL it points to a fixed IP address?
Also is the port number fixed?
Hello,
I am playing around with the Blinky example on my custom board, where I have one button and two leds. Everything works fine and I can control the LED2 and detect...
I have a question about PeerManager.
SDK: 15.3.0 example: ble_app_multirole_lesc (I changed the source from the sample) using device: EYSHJNZWZ (nRF52832)
When connecting...
Hi,
When I test nRF MESH application on android phone with other mesh device, after discover services, it always use proxy data in to write data to device for provisioning...
Hello there,
We are planning to use MQTT and nRF5 boards in the project. We've successfully tested out MQTT examples provided in the SDK using BLE router on Raspberry Pi...
Hi,
We are trying to establish communication between ESP8266 and NRF52832 over uart using Baudrate 115200, We are also controlling the ESP8266 boot and power through GPIO...
Folks,
I have read through a lot of threads on here trying to solve this and believe I have tried everything to no avail.
I am finding that I cannot get the nrf52832 to...
Is it possible on the central device to create secure and unprotected connections simultaneously with different peripheral devices? How should the peer manager be configured...
Hi,
I'm writing an application to communicat on BLE with an IoT device.
I connect well, and can write on characteristic but normally I should receive notification after...
infocenter.nordicsemi.com/index.jsp
<info> app: peripheral init ok <error> nrf_sdh_ble: sd_ble_cfg_set() returned NRF_ERROR_INVALID_STATE when attempting to set BLE_CONN_CFG_GAP...
Hi,
I was wondering if there is some kind of SIP client example code available (or in progress) for the nRF9160? For a new project, we are investigating to use the nRF9160...
I'm currently working with nrf52832 implementing bluetooth and spi functionalities. The bluetooth connection to PC is working fine, it connects and after that starts transfering...
Hi,
It seems I am unable to open the asset tracker application in SES. I get the following CMake error:
I've followed the nRF Connect SDK getting started app, and all...
