Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
We have an interesting difficulty, whereby after a period of time which varies never longer than 12 hours, often around 6 hours, our application disconnects from the network...
Hi,
I have NCS v1.0.0 on an NRF9160-DK v.0.8.3 and I am trying to run a program written before the SDK update. I can build and flash the program but when I try running...
Hi. I have a multilink central based project running on nRF52840 SDK15.0. I have added code from another example to do advertising as we want the central to advertise some...
Hi ,
I am build and run the source code of nrf Uart app from nRF UART App git repo. When I clicked on the connect button it opened a new sub window ,I know it is the list...
Dear all,
we would like to use nRF9160 DK as a CAT-M1 reference device for our local test purposes. Usually we use iperf tool for UDP traffic generation. Do you have any...
Hi,
I try to use the nRF52840 as a sniffer. I tried to follow ( https://infocenter.nordicsemi.com/pdf/nRF_Sniffer_UG_v2.2.pdf ) but I block in the 2.2.5 part.
When I run...
On the NRF52810_PS page, I find UART is exists,
But on the sdk_15.2.0, NRF_UART_Type is disappear at nrf52810.h.
So I can't call any nrf_uart_xxx functions and UART...
Dear All,
I know similar questions have been asked before but I have read around quite a bit and I couldn't find an answer to my specific problem.
I have a ble application...
Hello All,
I am working on the simple advertising example.
I am using SDK_V_15.3 and NRF52 DK board.
I want to create a timer for on / off the advertising repeatedly...
Hello,
I have successfully flashed and run the mqtt-simple example from the nrf samples with the default configuration.
If I run it 10 times in a row, the getaddr with...
Hi.
I struggled to migrate ble blinky example of nrf5 (nrf51422) to nrf51822 using KEIL (SDK5 v12.3) but failed
Here are what I tried.
Firstly, I changed target device...
Hello,
I want to create a program for communication and control between the NRF module and the desktop. I followed the instructions Installing from https://github.com/NordicSemiconductor...
Hi!
I'm working on a toy based on the nRF52810.
The BLE requirements are very low:
- Peripheral only
- 1 link only
- No bonding/pairing, no encryption, no whitelist...
i can create three service each with one notifiable characteristic. i am using nrf connect to test if it is work and i am able to send data through UART Rx and then enabled...
HI,
I'm use nrf51822 and SDK 10. I want to use APP_ERROR_CHECK function to show error msg, I did also enable LOG function to support this, but it do not work.
here is...
