I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi, in order to be familiarized with the transceiver we have purchased an evk nRF9151 from Nordic.
I have some questions because an issue appears when I try to modulate...
hi guys,
I am using the nRF54L15 for software development. I have a requirement to define a space in the chip's internal flash for data storage. I referred to the soc-flash...
I have been experience that the if the device under a DFU process reports the error BUSY, because the external flash on the device is used for fileaccess the DFU process from...
Hi nordic support:
Our product uses the nRF9151 and prepare for GCF certification testing , which need to capturing LTE mode trace log .
We first intend to try running...
Hello everyone,
We are currently working on a project that uses the nPM2100 to power an nRF52840. Our application requires automatic enabling break-to-wake mode each time...
Hello DevZone,
One customer used Timer+PPI+GPIOTE to simulate an UART. Now it works fine.
However, when there is other timer's interrupt, the simulated UART may lose some...
Hi, I just received our nRF54LM20DK, and am trying to get a functioning BLE sample on the board. Many samples are supported, however I have not gotten a single one to work...
Hi,
I have a question about SPIM. Is it possible to have two events via DPPI that will start different SPIM transfers for the same SPIM channel?
What would happen if a...
I have the board: NRF52840-DK PCA10056 3.0.3 2026.5 1050266921
Is it possible to use OB J-Link to debug STM32/RP2040 MCUs connected to P19/P20? Or OB J-Link support limited...
Hello, My nRF54L15-DK has suddenly stopped working, and it appears to have a hardware-level power failure.
The board was working normally the previous day while running...
We are using CMakePresets.json extensively in our project and rely on the condition field to control which presets are visible depending on the host system.
However, it...
Hello,
We are using the nRF52840 with SDK 17.1.0, SoftDevice S140 v7.2.0, and the secure bootloader (nrf_bootloader.c).
Our application relies on reading NRF_POWER->RESETREAS...
Hi there,
One of the functions of the DECT MAC layer is to allocate radio resources to RDs. According to the standard, the MAC layer does that using special beacon messages...
Hi,
I'm working on a wireless sensing project using the nRF54L15-DK (PCA10156) where I need continuous RSSI measurements at 2440 MHz. I'm accessing the RADIO peripheral...
Hi,
I am working on an nRF52832 using nRF5 SDK 16.0 and I am seeing inconsistent behaviour in the RESETREAS register. During a power-on reset, the value is usually 0 but...
