Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hello,
My rigado BMD 200 board suddenly stopped responding. the Jlink interface cannot connect
I tried nrfjprog --recover with no success.(says cannot connect)
in segger...
I am using nrf51822 with sdk 6. I was using double bank ble dfu for the firmware upgrade. But now I have to switch to single bank dfu since my code size has exceeded the maximum...
hi ，
image 1 、
image 2、
image 3、
I now use nRF24LU1P for Bootloader upgrade, using the routine is the official website of the C# Lu1BootLdrTest project, nRF24LU1P...
Hi,
I have a nrf24lu1p usb dongle by hand and I want to know the flash size.The package marking is:
nRF D
LU1P16
1219AC
I am not sure whether the chip has a 16kB flash...
Based on multi-protocol add private agreement GZLL matching procedure, no matching success;But separate GZLL agreement can be successful, not any way to solve this problem...
Hey devs!
We'd like to add additional fields in the manifest.json when generating (or after generating) the zip file for DFU. We need these fields to make additional compatibility...
Hello,
I am using the nrf 52 dk with the soft 3.00. I am doing the Beacon Transmitter Sample Application from infocenter.nordicsemi.com/index.jsp.
I was able to compile...
Hi
I am using nrf52832 QFAA-R.
I wanted to know if there is a difference between SPIM current when SPIM is:
stopeed
started but not active.
Thanks
Yar...
While analyzing the current consumption of my nRF52832 Dev Kit I noticed that the system on low power current was significantly higher than expected. To further investigate...
i have connected the swdio , swclk , vcc , gnd , reset with the respective pins of the nrf52SDK ,but when am debug the nrf52sdk , am getting the following error.
ERROR...
Hi all,
I am testing out the BLE_APP_UART example on a NRF52DK and I am using SDK13.0 (PCA10040, S132).
I have change the app advert timeout to be 10 seconds.
I am...
I am trying to combine both the SAADC and BLE libraries to be able to read a value from my sensor on the analog pin and then send it over Bluetooth LE to a central dongle...
I plan to merge the protocol sack and the application. At the same time download in batch to 52832 by using the SWD. But the tool(nRFgo Studio) offered officially is not fit...
Using existing examples in SDK13, I prepared ADC sampling app which works fine in ESB TX mode. Works well sending frames at 10ksps, and I can also put it to 'standby mode...
