Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
I recently saw that SDK12.0 provides a Bootloader Cryptography module. I'm not certain after reading the documentation that this module can support my use case:
infocenter...
Hi,all. i want to use nrf51822 to generate a 3.3M hz wave,but i don't know how to do this.Can this chip reach so high frequency？Can someone help me? Thanks ！
I'm trying to implement context switching from handler mode to thread mode using PendSV. I set the PendSV pending bit inside an ISR with SCB->ICSR = SCB->ICSR | SCB_ICSR_PENDSVSET_Msk...
Compiling nordic project I get errors:
compiling main.c...
..\..\..\main.c(37): error: #5: cannot open source input file "softdevice_handler.h": No such file or directory...
I am not sure if this is a limitation with Keil or Nordic SDK. I made another copy of ble_app_uart inside SDK_11 s130 and renamed it with a much longer name. I tested that...
I'm using the nRF SDK5 v11.0.0.
I'm trying to test out UART Logging in the simple blinky example bundled in the SDK.
I added NRF_LOG_INIT() and then a NRF_LOG("Testing\n...
Hello everyone,
I am trying to implement a bootloader to my application to be able to enter in DFU mode.
I am using nrf51822 (32KB ram 256 flash) and s130.
I have taken...
My understanding is that the nRF51 is known to need a fairly stiff external pull-down resistor on SWCLK to avoid noise putting the chip into debug mode. I note that the nRF52...
I'd like to know how to implement a bootloader for the Nordic SoC nRF51822-QFAA-R in order to boot the softdevice and some firwmare. If will be great getting an application...
Does nRF52832 have battery monitor?
I can't find in the datasheet if there is an externarl circuit to monitor the battery. I'm using a CR2032 coin cell battery.
Tha...
Hi,
I'm developing some firmware that will hopefully run on a few different kinds of nRF52 device.
Is there a way of detecting if the DC-DC converter's inductor/capacitor...
Following situation:
My device acts as central (connecting to ble sensors) and as peripheral (transmitting and receiving data from mobile). Several services (Heart Rate...
Hello,
I followed this tutorial:
devzone.nordicsemi.com/.../
and added the RTT files to the project, however, after I compile i get this message :
and when...
Hi guys,
I am using the RFduino nrf51822 chip. I am using the TIMER2 interrupt and it works fine. But when I try to use the BLE along with the timer interrupt both don...
Hi,
I have have one ble project which is using softdevice s110. so that i want to extend this project by adding DFU service to it like shown here
devzone.nordicsemi.com...
