I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I want to stop advertising for 8 hours
but when I use
sd_ble_gap_adv_stop();
sd_ble_gap_connect_cancel();
It starts advertising after 1 or 2 secends again.
I think...
Hi,
I followed the tutorials shown below:
infocenter.nordicsemi.com/index.jsp
I downloaded SDK v11.0 and loaded S130 SoftDevice on my nRF51 DK. I use Keil uVision 5...
I am working on a bootloader for a client. I’ve been looking at the DFU example that Nordic has. The BLE version of the DFU needs to have the special format using the “nrfutil...
hi:
I use bootloader example of sdk 9.0.0 ,most cases worked fine, but I got gatt error sometime when I begin DFU. I had changed the dual_bank_ble_s110 into sigle_bank_ble_s110...
The nRF51 reference manual says that GPIO PIN_CNF registers are retained registers and that "a retained register is a register that will retain its value in system OFF mode...
Hi,
I'm trying to add second service on the fly, while SD running. After adding it, I'm trying to send service changed notification, but it don't work. Below is code used...
Hello.
I test nrf51822 central and peripheral.
I want to change radio channel frequency about nrf51822.
I test source code as below.
nRF51_SDK_10.0.0_dc26b5e\examples...
there is an error on softdevice on src\ll_adv.c on line of 659 . what is the reason?
this is my adv init
#define DEVICE_NAME "navid" /**< Name of device. Will be included...
hi
I want to know whether we require MCU for enabling "Enhanced shock burst mode " or when we set the CE pin to high for making RX that time automatically this will enable...
Hi everyone,
I am using the nRF51822, I have an issue of programming the bootloader.
It is said that the flash is not erased. But I just did an erase all before programming...
Hello,
I have two questions regarding nRF52832 ADC, which are not documented :
what is the precision / tolerance of the internal 0.6V reference?
what is...
hello there,
I use currently 'ble_app_hids_keyboard_s132_spi_pca10040' app of SDK11 for my nrf52832_xxaa device on 'IAR' IDE. It utilizes sofdevise s132. I do not use the...
Hi
I'm encountering a problem in UART communication with nrf51422 on a custom board over an FTDI USB-serial converter ic.
When I send a string > 40 chars from the terminal...
hi
i have nrf51422 sdkv6 ss10 v1
i have timer2 inited
after something like 30 minute that it work right it stop without any system or ble event and it goes here
...
ibeacon noob here, I see several postings about implementing with different chips. Is there a preferred solution for an ibeacon for new designs? Thanks!
