Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
Hi
This is my first project to make my custom PCB.
I have a question about how can I uploaded my code with segger embedded studio by using nrf52840 dk?
For the hardware...
Hi,
I've create an v2.4.0 SLM application in VS Code by copy from sample, and I am trying to enable trace function for cellular monitor tool app, in order to LOG the packets...
During our evaluation of MQTT, we observed that if we send data every five minutes, the server stops receiving it. We currently believe this is related to CG-NAT, which drops...
Hi I am getting fatal errors when building most of the exercises in the Wifi Fundamental course. I have attached terminal output from building the wififund_less4_exer1_solution...
I have code developed for the nRF52832 based on the Zephyr RTOS. If I switch to the nRF5340 with Zephyr RTOS, would it be possible to develop by simply uploading the additional...
Dear all:
I have built a project(ex: matter bulb) in Nordic SDK, the generated load is zephyr.hex which size is about 2345kb ;
Then I open nRF Connect Programmer, and...
I'm attempting to get our wearable remote to interact with a GoPro using their API and am getting the error in the subject line when attempting to start scanning. I've checked...
I am working on scanning and connecting to an iPhone device in NRF52840dk, but I am not able to receive my iPhone while scanning. If there are any different ways, please let...
Hello!
Looking for some guidance on how I should start debugging an issue I'm experiencing trying to get the Zephyr fdc2x1x sample code running on a custom PCB that uses...
Hi everyone,
I am working with the nRF SDK v2.0.4 for VsCode and with the nRF52840 DK.
I want to develop an application that transfer in real time the data collected...
I'm essentially building a BLE to UART gateway to allow our microcontroller device to talk to our apps. The BLE section is the nRF52840 and I'm trying to simply use it to...
I am trying to install the nrf connect SDK on my Macbook M3 Pro. But i am unable to do so. Neither VSCode extension nor the Toolchain manager works for me.
Clicking install...
I'm currently troubleshooting potential timing-related collisions associated with the NRF radio. I use a custom protocol on a single specified channel (no frequency hopping...
Hi, I have a custom board built around a nRF9161. When I test with the at_client only AT+CGSN=1, AT+CGMI, AT+CGMM and AT+CGMR return with the expected string. All other commands...
Hi all
I'm working on custom board build with an nrf9161. Right now I'd like to use a gpio as input with interrupt for i2c captor icm20948. So for I've searched and I think...
