Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Dear All,
I would like to know information about QDID for nRF5 SDK for Mesh v4.2.0, we are developing costumed equipment using NRF52833 and we need to start the process...
Dear Nordic support team.
Our product nearly complete Rnd stage.
We face only one thing relate to "Cannot reconnect after unpair device with smart phone".
debug wit...
How can i give command from android device to ble board to get the percentage, temperature, or reset or shutdown the device with the help of receiving command from android...
I'm trying to register the SIM card of the 9160 DK at nRF Connect website,
but the website is always showing "still working..." for more than 15 minutes.
Do you have a...
Hello,
I am experimenting with setting up a network via grouping in the following manner.
Bulb_1 will be put into identification mode, and Switch_1 will detect Bulb_1...
Hello,
I am trying to send gps data using MQTT protocol. For this purpose I wanted to combine MQTT simple example with the GPS example. I added all the methods/dependencies...
Hello,
I started to work witn NRF Connect SDK with nrf52840-dk? I mapped lots of peripherals to NRF Connect SDK. There are no problems. However, I try to map nrf_fstorage...
Hello
I am testing out a blinky FreeRTOS example that's a part of the SDK and would like to use SystemView to visualize context switching and tasks. Are there any steps...
Hello,
We're using a BLE connection configured with a 15ms connection interval, and a radio event notification configured to fire 800us prior to a radio event. I'd like...
Hi,
I trying to create a blank Zephyr project for NRF52 and want to use SES. But I could only open pre-existing samples and there's no way to create a blank project.
Appreciate...
I want to create server and client in nrf9160 not through LTE. only transmit on locally in nrf9160
//prj.conf # enable libs CONFIG_NEWLIB_LIBC=y CONFIG_NEWLIB_LIBC_FLOAT_PRINTF...
Hi support team,
In PS, it stated the sensitivities for ideal BLE transmitter, I would like to know:
o Sensitivity at 1M PHY DLE 255 octets , Dirty Transmitter on
o...
Hi,
In the documentation [1] for 802.11.4 for nrf52-sdk it is mentioned that the documentation is for the nrf52840 soc only. Where can I find documentation regarding 802...
I would like to add FOTA via HTTP to mqtt_simple example
please describe how to do that, and how to test the update
I know I need to add the following modules via...
