Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
Hi DevZone,
I want to perform USB bulk transmits to a host device while using the app_usbd library. I am using SDK 15.3 and the s140 soft device is enabled.
I have found...
Hello Nordic Team;
The Vdd value range for the nRF9160 is 3.00 V to 5.5 V. We will use li-PO battery in our system. Can I power the nRF9160 directly from the battery without...
Hi,
I am using Nordic thingy 52 for my application, Now I need to blink LED for 5 seconds on Board when ever a condition is satisfied. But in schematic of Nordic thingy...
Board: nRF51-DK (nRF51422 chip)
SDK: 12.3.0
SoftDevice: S130
Compilation settings
Optimization level O1
Debug information generated
I have seen lot of...
Hi.
I am going to make my own PCB with nrf52832.
Before making it, I have to check debugging through P20 in nrf52832 DK.
I have two nrf52832 DKs with SDK17.0.0....
Platform: nRF5340-DK
Tools: I am using SDK 1.5.0 (but seen on earlier SDKs too)
Configuration: Using high speed spi pins whether for SPI1 or SPI4
If I use SPI1 I see...
Hey guys i wanted to ask you for help on IOS BLE i am currently seeing that nRF Connect seems to work fine over BLE Connection with some devices on Android and as far as i...
Hi,
I'm using NRF52840 in order to connect to a mobile app via BLE.
When connection to IOS, I have an event called BLE_GAP_EVT_PHY_UPDATE_REQUEST.
This event handle...
Hi,
Greetings!
We are exploring nRF9160 SIP DK and Thingy91.
Here we have understood that it has GPA and LTE-M.
We wish to use it for India region in moving objects...
We are using the advanced UARTE library to get advantage of EasyDMA to receive data from a LTE module.
We also implemented hardware flow control. THe problem is that the...
Hi fellow devs:) I'd really appreciate some advice on this please. I've come to a bit of a dead-end. Hopefully you can spot a mistake I've made. I am trying to produce a low...
Hi,
-I have a custom board using nrf 52832 and I have interfaced sensor using an SPI interface. -I am using SDK 15.2.0 and SPI driver. -I am collecting raw data and send...
Hi, When I test the SPI with extern flash W25Q64, The SDK default configuration seems to be too low powe, After SPI initialization is complete, The GPIO drive is configured...
Hello All ,
I want to use nRF 52810 Bluetooth feature in one of my application. The application is supposed to be highly power optimized. Sharing below some details about...
