I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I am trying to send a single adv packet when a certain condition in the application is met. To do this I am calling ADV_start for the initial adv packet and then...
These questions are in the context of using an nRF52840 in a serialization application. But I don't believe this will impact the information I am trying to understand. The...
I want to program the firmware into a nrf52840 on our custom board to be the NCP and do the DFU over thread. I can not use the DK board and have the nrfutil load the firmware...
Hi,
Our application uses MQTT over TLS to talk to a MQTT broker.
The MQTT APIs used are like in the 'mqtt_simple' sample code.
When mqtt_connect is called with invalid...
Hi,
I'm designing an application using SEGGER Studio for the nRF52832. I have based my application on the template peripheral example.
What I want to do is to trigger...
Hi--
I tried to implement an internally managed RTC using the app timer library, but came to find the error on that is too much for an RTC (~25 min lost over a few days...
I want to know which pins serve the purpose of TX and RX in nRF51822. I suspect its the ANT1 and ANT2 but i want to confirm and also if the following would be a good way to...
I just buy nrf52840 Dongle.
I connect nrf52840 Dongle to my USB port and open nrf Connect.
I look at guide https://devzone.nordicsemi.com/nordic/short-range-guides/b/getting...
Im using sdk 15.2 with 2 nrf52840 boards, i would like the server to connect to a particular client. How to add the devices to whitelist in sdk 15.2 ?. I have gone through...
Hello,
I am working on a scanner code, I have initialize my scanner with this parameters.
and in nrf_ble_scan_init()
It is getting reset once in the beginning like...
Hi,
without any obvious reason one of our nRF52840 DKs stopped being visible over the USB (J2) interface. The nRF52840 is still functional and can be programmed from another...
Hi. I'm using nRF52832, SDK13.0.0, S132.
First of all, I already know this Q has lots of Q and A.
But I'm so confused which case do I pick.
In my case, iPhone has...
I am a student studying zigbee. We succeeded in turning on/off the LEDs of zc_light using examples of zc_light and zc_switch. The question here is, where do you send and receive...
I am trying to duplicate a RF remote control which uses a Nrf24L01+ IC.
I have temporarily connect the SPI interface of my test chip to the SPI pins on the remote, and transmitted...
