Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
Hi! I'm developing an augmented wearable project using Bluetooth (eg., Smartwatch). I'm planning to use the nRF52810 chip for it. We are just going to add a couple of sensors...
Hi
win10 64-bit system。Reinstall the system and rebuild the development environment。Reinstall the system and rebuild the development environment. Can't solve the problem...
I can see in Segger Embedded Studio v4.52 under the Build Tab, there are two methods to build the project.
1- Build > Build zephyr/zephyr.elf
2- Build > Build solution...
sdk16.0 ble_peripheral/ble_app_hrs example
I start on nrf52840 DK with the SES
I run the following commands
nrfjprog --recover
nrfjprog --eraseall (?? just because...
I want to add peer to my project_ manager_ Init() implements pairing binding and whitelist. My project is S112 under pc10040e directory The reference routine is e: workspace_...
I want to test the mesh,but Idon't know hao to fine the path to nRF5SDK instance
..\nrf5_SDK_for_Mesh_v4.2.0_src\examples\sensor\server\sensor_server_nrf52832_xxAA_s132_7_0_1...
We are developing a device that has different "modes", and in some modes it acts as a HID keyboard and mouse, but in other modes it does not. This device connects to iOS and...
Hi guys,
I am using the nRF52832 board and after I enabled my device to measure the temperature and return this value, now I will like to save that value in non-volatile...
Hi,
Had a project working and compiling beautifully, all ready to go, last thing to do just upgrade the SDK from 17.0.0 to 17.0.2 and the s132 7.2.0
So I change the...
Hi
I start in programming on nrf9160 DK with a sensor BME280. I followed the tutorial "getting started part 2" (https://devzone.nordicsemi.com/nordic/cellular-iot-guides...
Hello, dear sir:
In my opinion, HFXO means external oscillator, I need to buy a external oscillator because it is not exist in nRF9160?
HFINT means internal oscillator...
I use sdk16 on nrf52810 for development, but I want to use long broadcast packageada. What should I do?
A short broadcast packet can only be 31 bytes
thank you!
To the kind attention of Nordic support team,
I was reading in peer_manager library that when a ble connection is established, using the connection handler as a parameter...
Hi ,
In our actual design, we are using nrf52810. We have done all our development on nrf52832, as there is no Eval Kit present for nrf52810. We are porting our development...
Hello,
I can see RTC drift of around 14 seconds in 1 hr when I select the internal RC oscillator in sdk-config of nrf-calender example.
Is this much drift expected? In...
