I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
Hi,
We're developing a system composed of one device with an nRF running as central, other device with an nRF running as peripheral and desktop and mobile applications...
We are looking for BLE module for Social distancing application.
We want to use Only BLE tags to estimate relative distance with respect to nearby tags within 5 meter range...
Here is the code i am writing, yet leds dont blink-
#define LED1 BSP_LED_0 #define LED2 BSP_LED_1 #define LED3 BSP_LED_2 #define LED4 BSP_LED_3
int main(void){
bsp_board_init...
Hello,
I am evaluating what the best way is to solve this problem: We have 2 network interfaces on our board. We would like to be able to switch between them dynamically...
Hi, I'm a beginner in working with these Nordic Development Kits. I've been following the steps outlined on the Nordic website for getting started with a nRF52840 DK. It tells...
hi,
I have 2 PCA10056 and few PCA10059 for BLE mesh testing.
need to configure dongle as provisioner.
unable to configure mesh provisioner example(also other client...
Hi,
I am working on a project which will connect to device having static mac address . My job is to make sure that the device will connect to device having BLE_GAP_ADDR_TYPE_RANDOM_PRIVATE_RESOLVABLE...
Hello,
I wanted to replicate and build the LED Button Service using my own custom service. I used the template BLE project as a starting point.
I am using nRF52 DK, and...
for (int i = 0; i < LEDS_NUMBER; i++) { bsp_board_led_off(0); nrf_delay_ms(500); bsp_board_led_on(0);
}
in this code only the first command gets executed.
It turns off...
Hi,
We have several boards on hand which fall into two categories:
Category A: Our application has been programmed with JTAG in the past
Category B: Out application...
Hello!
I'm trying to DFU an NRF52 device on a custom board using nrfutil
I'm able to DFU the device using the NRF Connect v3.3.0 software together with an nrf52840...
Hello,
My problem statement is something like this:
Implement a Transmit Enable (TxEn) on a GPIO pin.
TxEn should be initialized low.
TxEn should be pulled...
I am new to Nordic and i am using nRF52840 DK, - SDK 15.2.0 - s140. I have written an application by modifying the Heart rate Monitor example. My program acquires and sends...
hi,
I am working with usb dfu bootloader for nrf52833. I set the bootloader entrance mode to GPREGRET only. before enter bootloader, I set NRF_POWER->GPREGRET = 0x00000001...
I downloaded SDK V17.0.0.9 and opened BLE_APP_UART example from /ble_peripheral folder on IAR EWARM. I choosed ble_app_uart_pca10040e_s112 and compiled without problems. ...
