Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
Hi ,
I ran the example "zephyr\samples\bluetooth\scan_adv" on the nRF9160 dk kit .
It says the following error
"
2020-07-16T02:22:00.682Z DEBUG modem << *****...
Hi, everyone
A LPN ( Node-LP ) had selected one of nodes as its friend ( Node-F0 ), if Node-F0 is taken away, will the Node-LP automatically reselect other node as its...
I read somewhere for new project we should use nrfx driver because in future old nrf_drivers will not be support and improve. All examples in sdk15.3 as I understand used...
Hi All,
I am trying to implement a battery level reading app using NRF52840 DK. It seems I am receiving a timeout from saadc.
In order to run on the Lithium battery, should...
Hi,
I programmed two thingy:91 to return RSRP and RSRQ to a server. On is running with LTE-M and the other with NB-IoT.
I found something that seems strange : +CESQ: 99...
Hey everyone, I'm trying to use the QSPI module (again) to interface to RAM, not FLASH. I'm not really sure if this is possible, but we'll get there. Right now I can't get...
I've been tested for BT SIG however have met error which sent 0xc000 and got 0xc000. I expected to receive 0x8xxx. Command is LETestEnd.
I tested with nRF51822 customer board...
Opening a project in SEGGER Embedded Studio I have annoying "no entry signs" (white minus sign in a red circle) on the left side various items in a project, whereas most of...
Working with nrf52832_mdk and using basic GPIO functionality, I am unable to toggle the GPIO pins P0.0 or P0.1. The code I am using is quite simple and I am able to toggle...
Hello,
I am working on the mqtt sample from ncs\nrf\samples\nrf9160\mqtt_simple. Mostly the nRF9160 connects to the MQTT server in the first attempt. But sometimes I observe...
Hello,
I work on nbiot evaluation and i try to send udp data from my basement.. I boot and attach network from ground-floor and when i'm on PSM mode im going on basement...
I want to run the board at 1.8V and run the uart and spi examples on my laptop. What should be my configurations and which micro-usb port shall I use to connect with laptop...
Hi,
I'm trying to send custom messages between server and client, based on the light switch example. I've modified button_event_handler and the client was able to receive...
Hi Nordic team,
I have an issue: I have to program/flash my mesh application together with softdevice140, mesh-bootloader and device settings page on the nrf52840 chip....
