Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Nrf52 SDK12.2 armgcc
I have a button on my device (peripheral) that when pressed starts a timer for 30 seconds.
During that 30 seconds, I would like to have the device...
Hi everyone,
I'm trying to use sscanf on my nordic device, and I get an issue with the following exemple (this same code works on my computer)
int d = 0;
float f =...
I have copied the blinky example:
/* Copyright (c) 2014 Nordic Semiconductor. All Rights Reserved.
*
* The information contained herein is property of Nordic Semiconductor...
.\_build\nrf51422_xxac.axf: Error: L6218E: Undefined symbol app_timer_init (referred from main.o).
.\_build\nrf51422_xxac.axf: Error: L6218E: Undefined symbol app_button_disable...
Hi all
Is possible have DFU in the peripheral side to update a Central app program? Is there example doing it?
I have a Peripheral (custom board nRF52 dongle) connected...
Hi
We use the nRF52832 together with other devices in a housing. Some of the other devices may produce quite a lot of heat. Therefore we wanted to use the temperature sensor...
Hi,
i am trying to flash the softdevice bootloader in Sparkfun nRF52832 breakout board using RPI2 + openOCD through SWD. debug port initialize is failed all the time.i...
I have a couple of questions regarding Radio transmission for BLE.
Is the radio driven by one of the HFCLKs? If so, it confuses me how a 16M clock can drive/derive...
Hi,
I have initial flashed boot loader and application based on SD version 3.1 and SDK 12.2.0
with
DFU_APP_DATA_RESERVED CODE_PAGE_SIZE * 3
FDS_VIRTUAL_PAGES 3...
I am using a nrf52 development kit as a peripheral to send data . It is working fine if I use the nrf Toolbox app on my phone, but is there anyway that I can see the 'raw...
Hi,
I configured openOCD and gcc compiler. But i got following error.
i gave following command on terminal.
i created one file that is manual.cfg
and contain in that...
Hi all,
someone can please explain to me how works the indication?
How can i read the value of cccd in the APP?My problem is understand if the APP is ready to receive...
First attempt at implementing buttonless dfu; assistance would be greatly appreciated. Using SDK v11 + s130 + nRF51822.
Please note that iphone screen captures supporting...
Hello,
I am still having troubles with the BLE_GATTC_EVT_TIMEOUT. The problem is that the error is not happening frequently and is hard to reproduce. It is also hard to...
I was building my own custom application that connects a nrf_drv_timer to an ADC start trigger using PPI on an nRF51822 and I could not get it to work. I asked a previous...
