Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hello,
I'm trying to get the new SDK up and running on my OSX machine. I would like to make the blinky example work on my PCA10003. So, I copied the blinky/pca10028 folder...
Hello, Do you guys know if it is possible to generate a stable 38kHz signal using the Nordic?
I have been able to generate the required frequency however I am observing...
Not a question but thought worth mentioning.
developer.nordicsemi.com/.../
Good News
PWM library changes seems to have made it into the release.
Bad news:
Looks...
Hello,
I am working on an nRF51822 custom board application which is reading data from external sensor through TWI. It is based on the MPU6050 driver available in the SDK...
Hi there,
Before I asked this question, I have searched similar question about TWI example, but it seems there were some guys looking for such example as well. Not sure...
Hello
I try make a firmware update with nrf toolbox for iOS and i have a popup with "Please enable Service Changed Indication in your firmware".
In code, I have an error...
while I'm trying to compile my code, I got an error :
".\Objects\ble_firmware_v1.axf: Error: L6405E: No .ANY selector matches main.o(i.app_error_handler). "
this error...
I wonder if GPIO could safely be used for byte writes to the OUT port.
I have an 8bit (+control signals) peripheral connected to the GPIO and so far I was doing read-modify...
I will be using a 3.7V LiPo to power my NRF52 system. As far I understand, using the internal DCDC regulator is a better choice as it can save power compared to internal LDO...
I am running the UART example with the S110 softdevice on nrf51822. Sometimes my application transmits more data than can be carried and backs up. So the main thread's transmitter...
Not really a question, but congratulations to Nordic on getting their chip onto the Micro:bit(is it the nRF51 or the new nRF52?). Looks like a cool device. I'll be hanging...
Hi,
I want to change the device name before advertising. But it looks like I cannot open the adv pipe.
I have set writeable device name both from air and from application...
Hello
I try make a firmware update with nrf toolbox for iOS and i have a popup with "Please enable Service Changed Indication in your firmware".
In code, I have an error...
I need to connect to a LIN bus and Bluetooth on the same device. I'd like to use the ARM processor on the nRF51822 based module (PTR5518) to handle the LIN bus messages. LIN...
Hi,
After looking around it seems like the I2C example that used to be in the older SDK is currently not available anymore. I was wondering if it was replaced with anything...
