At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
I'm using app_scheduler to pass UART events in the "main thread". I'm storing multiple data types in a struct (arrays, integers) and I've set the max event size to the size...
Hello Team,
I am using the OT-nRF52840 source and working on the end device. I want to add the I2C(TWI) support in my end application, but as soon as I add any API it shows...
My problem is similar to this
https://devzone.nordicsemi.com/f/nordic-q-a/64696/projects-for-writing-into-flash-memory-does-not-work-on-nrf52840-dongle/264746#264746
except...
Can a "Pin Reset" recover the nRF52810 part if the part has encountered a slow voltage rise, greater than 60 ms, from 0 - 1.7V (described in the image below)?
Hi, I am new to nordic and zephyr and I have a sensor (Melexis - MLX90641) and I would like to test it on a custom board using nRF9160.. I add the sensor into the dts files...
When I open the nrf connect sdk project, it goes like this,
How can I fix it?
Creating solution direction_finding_connectionless_rx.emProject cmake -GNinja -DBOARD=nrf52833dk_nrf52833...
Hello,
I am preparing to develop a design using the nRF52840 and would like any guidance or consideration for an LDO usage. I have found some previous mention regarding...
At 1Mbps, UART will lose data when receiving. When I set it to 230400bps, it works well. I looked at the SDK code and found that too much time was spent in the receiving code...
Hi,
I had asked a question here few months back, about the maximum RSSI that can be seen on the nRF52832 chip.
https://devzone.nordicsemi.com/f/nordic-q-a/73578/maximum...
Hello.
We have several of our own manufactured boards, containing the nRF9160 cellular modem chip.
We use it for HTTP and HTTPS connectivity, on an application based on...
Hello. We are developing using nrf52832 (S132 v7.0.1, SDK v17.0.0).
I'm looking at how to encrypt a string with AES CBC. Below is the code we are considering.
Currently...
Hello.
I'd like to split an external QSPI flash chip so that part of the memory is accessible as raw blocks, and the other part holds a filesystem such as fatfs. Essentially...
Hi
I am using NCS version 1.5.0, I need to drive the GPIO pins of NRF5340 DK using the below library
"#include <nrfx/hal/nrf_gpio.h>"
While trying with this header...
