Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hi
The Product (NRF52832) was upgraded from SD 4.0.2 to the SD6.1.1.
During the pairing procedure the sd_ble_gap_data_length_update() returns a NRF_ERROR_RESOURCES error...
I use SDK16.
test fstorage write data.I find fstorage is busy appears when BLE sends and receives data.
for example main.c :
line 206: fst_erase_test(); line 207: NRF_LOG_INFO...
I am trying to implement the Simple On Off Server model in an existing project. In main.c I did the following:
1. In models_init_cb(), I added the following lines:
2...
Hello. I'm trying to make a product by running nrf51822 as an observer role.
This product will only use passive scanning and will not transmit any data.
How much energy...
Hello,
I have some issues sending valid information to nRF Connect app by bluetooth using the Aduino Nano 33 BLE with nRF52840 on it. I am using Arduino IDE and the ArduinoBLE...
Hi all,
The project I am working on consists of a BLE peripheral, a BLE central and an enhanced shockburst device. I run into a problem in the code of the peripheral:...
In a project based on Softdevice S132 7.0.1 employing the Softdevice timeslot API, I noticed that the nrf_radio_signal_callback_t function passed into sd_radio_session_open...
Hello,
I am using UART_1 to receive GNSS data. For UART_1, baud rate is 115200bps. On terminal, I can see the correct data when baud rate is set to 115200bps. When the baudrate...
Hi, i am using nrf52840 development kit , four servo motor . using 15.2 sdk version
here i am controlling the angle using adc values , i am done with one servo motor . pwm...
Hi
I am modifying the scanning and advertising paremeters for coded (125kbps).
I made the following changes in advertising
.primary_phy =BLE_GAP_PHY_CODED, instead of...
Hi All,
I am using nRF52832 SOC for my development. I would like to buy a packet sniffer for my BLE development.
Can someone please suggest a suitable device for this...
Hi
In the SDK, Replay_Cache_Entries is assigned a value of 40, which means that Replay_Cache can only process 40 unicast messages. That limits the maximum number of unicast...
Hi,
I am using
nRF52840
SDK 15.3.0
Keil IDE
The soft device is S140
JLinkRTTViewer for debug
Device has both Central & peripheral functions.
It takes about...
Hi,
I used(SoftDevice 140, based on the ..RF5_SDK_15\examples\ble_peripheral\ble_app_beacon )
m_adv_params.properties.type = BLE_GAP_ADV_TYPE_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED;...