At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello
Where is the the timeout for the Resolvable Private Address (RPA) defined?
only possible in the central?
can I change the timeout in the android nrfConnect...
Hi,
I am using nRF Connect (Desktop) v3.3.0 with a nRF51 dongle with the latest firmware to test my BLE device application.
My application contains 1 customized service...
Hi all,
My goal is to store large data which is approximately 300KB and send it using UART. To do it, I think I should the library of NVS on zephyr. I achieved to use it...
Hi,
I am trying to make a design for the m odule ISP4520 from ISP, which is basically a pcb with a nRF52832 and a lora radio.
However the processor on the RF52832 is not...
I need to share the LFCLK with an external device and I'm thinking on using an external oscillator like SiT1532AC-J5-DCC-32.768E
I'll set the LFCLKSRC registry as 111 (Apply...
I am setting up a build server that will take care of building our app for the nRF52 and creating the DFU files. For DFU package, I need nrfutil.
Everything is working fine...
The document infocenter.nordicsemi.com/.../nan_040.pdf shows the recommended sizes of the pads (0.275mm) and apertures for the stencil (0.3mm). To connect the inner rows of...
I have some nrf52382 nodes. I want to form two subnet in mesh.
if i using different provisioner to make subnet or something else ？
1. How to Create two subnets: Subnet...
Hi, I'm using metamotionR of Mbientlab that have nRF 52832 ( I attached the circuit of metamotionR )
but, I want to develop new firmware on this device. so, I started with...
Hello,
I have to implement ESB on nRF52 bare metal (using the RADIO peripheral). I can receive packets from the nRF24, but I need to implement the ACK, and I'm not sure...
Dear Nordic, dear Community,
I want to use the NRF9160 for a new IoT product row of our company.
The NRF9160 DK seems the perfect solution for evaluation and development...
Hi,
I have pca10059 and I need to remove FDS data during programming the device (for sure I do not want to remove bootloader). and it seems that nrfConnect could not do...
Hi,
I have some doubts on how the "nrf_pwr_mgmt_run" function works. As far as I know this function enters in SystemOn Idle mode, so the CPU is in sleep.
I tested this...
To the kind attention of Nordic support team,
I've got PCA10056 and PCA10040 default development kits. They are talking each other using using secured gzll, PCA10056 is...
Hi, I have RAK5010 Module which is based on nRF52840, and I also have the nRF52832 DK from nordic, and I want to program the RAK5010 using nRF52832 DK. Is it possible ? can...
