Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello guys,
I'm pretty new about embedded development. I want to transfer data by BLE (probably UART?) and then read from COM port of my win10 laptop. Can you give me a...
Hello!
I compare the timer every 1ms and process it. In order to check whether it can be executed every 1ms, I am going to refer to the register value by "TASKS_CAPTURE...
I would like to use Gazell along with BLE using the TimeSlot API. As part of this I need to set the Gazell mode to NRF_GZLL_MODE_SUSPEND while waiting for the next timeslot...
Hello.
I am trying to build project for thingy52 but since latest release of sdk for thingy does not work well with SES -> https://devzone.nordicsemi.com/f/nordic-q-a/27311...
I am trying to interface BMI160 Shuttle Board to the nRF52840 Development Kit using TWI interface. I am using IAR Systems IDE and have modified the "twi_sensor" Example code...
Hi,
I am using ncs V1.0.0
When I configure P0.5 as input it takes 37uA current. (Interface with PCA63548 / LIS2DH Interrupt)
If I not configure the pin as input getting...
Hello .
We have an issue with the SPI channel.
We found out that when our GPIO config as SPI the CS drawn a lot of current when it connect to the slave device device AD7770...
Hello,
I am working on pc-ble-driver-py to design a central (using a DevKit with a nRF52832). At this point I am trying to perform a phy update procedure but I see it is...
Hi Everyone,
I am using PSM mode in my program and want to send data everytime when modem wakes up from sleep(PSM mode). I also want to turn off/on UART only when required...
Hi,
During startup the nRF sniffer extcap script does the following:
Which (at least on Linux) breaks applications having open serial ports.
Why not instead use...
Hi all,
I have mqtt sample on my board, after I added MCUboot module from Configure nrf Connect SDK Project, when I try to debug, it gets stucked at :
#elif defined(CONFIG_ARMV7_M_ARMV8_M_MAINLINE...
hi,
nrf52840 BGA footprint P0.22 config as UART0 RX mode, don't receive any data, but config as other pin P1.06, work normally.
and I also test QFN footprint with nrf52840...
I have nrf52832 platform and my version of softDrive is (nRF5_SDK_15.3.0_59ac345). I red a lot of documents and tech support like these links but couldn't find my problem...
I have another MCU on the same board as the Nordic 52832. The firmware update image for the MCU is about 50kb in size, so instead of adding a parallel DFU for the MCU through...
