Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
I am working on a mesh network and i want to add a nordic thingy 52 to read temperature & humidity data over the mesh, let say to an nrf52 DK connected to a Raspberry Pi,...
I'm developing a Zigbee coordinator that works as an On-Off Switch for the Zigbee Profile HA: this connects to the Device Mains Power Outlet, again with the HA profile.
...
Hello to all,
I have a question about parsing zigbee commands when they present a payload.
I have a Coordinator that implements the Window Controller Device of the HA profile...
Hi folks,
Im trying to run the heart rate collector from a Visual Studio application and I have some communication issues with the connectivity device. I use a nRF52 Dongle...
I'm currently looking a bit into the bearer-layer internals of the nRF SDK for Mesh and noticed that there is a heap of instances where data needs to be transferred between...
Hi,
I am using nRF52840 and BLE coexistence (mesh and ble). I am able to connect to my board via BLE using nRFConnect for PC and a nRF52840-DK and change characteristics...
I'm trying to use DFU for the first time
I'm working my way through these instructions:
https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/getting-started...
The SDK v16 package has a board file for the nRF52833 board, PCA10100, however this seems to reference GPIO pins which are not present on the device:
What should these values...
We use the nrf52832 in twi-master mode. The connected slave sometimes needs longer to respond than the default configured TWI timeout.
The timeout is defined inside the...
Is it possible to generate a zip package containing both firmware and softdevice in such way that the soft device will be updated only if the current device softdevice version...
I have some module chip connected to the nRF9160 DK providing the sensor data over I2C line. In some state transition of the module the short reset pulse needs to be generated...
Hello, I am using BLE secure bootloader example on nRF52840 with SDK 15.3 and softdevice 61.1. I can see the bootloader protects the MBR page and Bootloader space using ACL...
When I run "AT+COPS=?" WITHOUT a SIM the modem always responds properly.
When I run "AT+COPS=?" WITH a SIM the modem does not respond as expected. I get error after approx...
Hello everybody.
I have been working on nRF52840 for a time. I am trying to flash the chip with ble_app_uart_c (SDK 15.3.0). I have applied everything essential, but my...
Good morning everyone,
I am facing an apparently common problem (reported with some variations Here , Here or here ) which is driving me crazy. In the linked discussions...
