I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
hello.
I am developing as nrf5-ble-multiple-role-example-master.
And I'm using nrf52832 chip.
When I send a message from the mobile app, I get a message on the SEGGER...
Hi All
I am now working in Channel Selection Algorithm (CSA), Bluetooth Low Energy. Basically, I would like to test both CSA 1 & 2, and also I would like to modify the CSA...
Setup:
SEGGER Embedded Studio for ARM (nordic Edition V4.18 (64 bit)
GCC
Windows 7 Professional
SDK: nRF5_SDK_15.3.0_59ac345
Issue:
In order to use the GPIO...
Eagle pcb and schematic reference designs on github are incorrect.
Reference nRF52840 pcb schematics and layouts are exactly the same for examples 2-6. I believe each is...
Hello,
I am using a nRF52840-DK with an HX711 in SES. I have been utilizing the code provided by Vidar Berg that can be seen here .
I downloaded the zip file, unzipped...
I'm developing the PCB schematic for a system using a nRF52 module that I found that suits my needs SKB369
At the same time I'm implementing a JTAG connector to flash my...
I was wondering: if the last sample of a buffer in the SAADC (using easyDMA and scan mode) is outside the limits, which interrupt would come first, the END or the LIMIT interrupt...
Hi, I am getting a BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST event since I increased the size of MAX MTU to 203 from 23. At first, I received INVALID PARAM error and then found out...
hello.
I am developing as nrf5-ble-multiple-role-example-master.
And I'm using nrf52832 chip.
When I send a message from the mobile app, I get a message on the...
hi,
I have developed light lightness model with the help of generic on/off and generic level model from the mesh SDK. And I have used these models by making changes in the...
Good afternoon,
I am trying to run the example "direct_test_mode" on a custom board based on a nrf52832.
I have succesfully run the example in two development kits ...
Hi,
I´m using nrf52840 with softdevice S132 and I wonder whether the ble_gattc_conn_cfg_t::write_cmd_tx_queue_size is a queue common for all connections or if it a queue...
I am currently testing DFU updates with nRF52. I have run into a situation where the upload of new image is interrupted for some reason. When I try to run the update again...
Target : NRF52832, SD S132 6.1.1. program on Eclipse.
Hello,
Intro :
I migrated to SDK 15.3 for my application and it works.
Then I migrated DFU to SDK15.3 too but...