At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hi all,
Because of my customer special requirement ,I need two or three USB in my project .
But 52840 has one USB.Can I extend 52840 USB interface with a USB HUB?
With SDK V14.2, I was able to specify internal flash address argument into nrf_bootloader_app_start(uint32_t start_addr) and was able to boot into the address. With SDK V15...
Hello, I have a problem when trying to compile the light server exemple for the mesh.
I use Segger Embbeded Studio 4.16 (even though i tried the 4.15), mesh sdk 3.0 and...
Hello,
I'm using NRF52840 module to make a customer device. I'm using nRF5 SDK for Thread and Zigbee v3.0.0.
I have a Thread mesh with some routers devices and one child...
I saw this BLE security issue and was wondering how Nordic deals with it. When the other side uses the example LTK from the BLE spec, can the softdevice automatically reject...
Hi,
Here's I want to do: Use static passkey to connect with central and peripheral. I'm useing peer_manager to doing this. 1. I've setup passkey in peripheral with function...
Hi,
while I tried the Power Profiler in the nRF Connect Desktop on OS/X, I got some error messages in the log (something like PPK Command Error). So I've installed the newest...
I run blue_app_hids_keyboard_pca10056_s140 sample on nRF52840-DK. I try to connect with Windows 10 PC, but PC does not discover Nordic_Keyboard.
I found advertising is sent...
We have a PCA10090 board and I followed all the steps of the nRF Connect SDK to install everything, including the files from repository, SES, etc. All is ok but I can't find...
Hello, I am working on a project that uses nrf52832 and I need to put that device and in the system on mode. For that, I want to measure the current in the system on and system...
The PWM (Pulse Width Modulation) peripheral coupled with EasyDMA makes an excellent waveform generator. However it has one drawback which I would like to request be added...
Hi, i use the saadc example(triggered by ppi+timer) with uart to get voltage signal and transmit to central device( another custom nrf52832 board), and the central prints...
hi .eveyone. i use 51822 sdk12.3.0 , i want to dfu app code with uart, but not use bootloader_secure and experimental_ble_app_buttonless_dfu. i do not know how to develop...
Hi
Im trying to figure out how to migrate my quite large older project from and softdevice s130 to using s140 in order to experiment with long range.
Besides changing...
I try to update firmware for nrf9160.
My environment is windows10 msys2 python3.7.3 run follow, (not success) ----------------------------------------------------------...
