Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
I am using nRF52832 with SDK 14. My app has bootloader and dfu. Everything was working fine with external crystal. I changed my clock source to RC and used these recommended...
hello, I have developed nrf52840 for multiprotocol ble/zigbee.
I want to simply send & receive zigbee packet not using zboss network.
I already tested example "wireless_uart...
I have two nrf52832 boards, both being developed with SDK v11 and the s132 soft device.
Board one is given commands over UART to communicate over ESB with board two. Board...
Summary of Issue: 8 dongles are used in a test system that each dongle will communicate with 1 device. Testing can start ok but after some runs, one of the dongles can not...
According to nRF52840 Product Specification v1.0, a ll the reference circuits are designed for use with a 50 Ω single-ended antenna. Why is the calculated result by AppCAD...
What would be the best example to start with my project which involves sending sensor data to mobile phone applications using ble? i have nrf52 DK and SDK 15.0
Thanks,
We're using RTT with an 52832 and it works fairly well, really can't complain much except...
On my PC everytime I launch a debug session I need to launch RTT viewer exe...
I'm using Rigado BMD350 evaluation board. I'm printing to serial port (COM3, speed 112500) using NRF_LOG_INFO.
However, the logging does not appear until debugging is...
In a recent project, me and my team have been trying to send data from 3 PTX devices to a single PRX device (the devices are all nRF24L01+) at a constant rate of 1600Hz from...
hi all!
Like two of my predecessors, I am trying to put a CR95HF into operation. I chose the nRF52832 DK as MCU (SDK 15).
[thread= https://devzone.nordicsemi.com/f/nordic...
I changed only source clock part to internal clock and it doesn't do advertising. When I debug it, it starts to run. When I finish the debug session advertising stops again...
Hi,
I've built a custom board with nRF52832, without other MCU like PCA10040. I use a FT232RL to bridge the USB to nrf UART, flashed nrf5 uart connection firmware ble_connectivity_s132_uart_pca10040...
Hi, I using nrf52810 with custom BLE profile and 4 sec advertising + continuous RTC. Device is battery powered (750 mAh) and PMDC motor equipped. Most of time (90% of day...
Hi,
I am designing my custom board with the nrf52832, which would perform the BLE and I2C functions. I wonder what necessary and basic peripherals it needs, like crystal...
Hi,
I would like to synchronize 2 Sensors with one dongle. So the problem is that we have two sensors and we want to start the measurement at the more or less (1 ms) exact...
