We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Is there any downside to enabling all of the radio "shortcuts" controlled by the SHORTS radio register to avoid and reduce delays in the transmit and/or receive sequences...
I've installed the ble_template_app on the nrf52832DK and the nrf52840PDK and the Adafruit nrf52 Feather (almost the same as the nrf52832DK). I've modified the configuration...
I am reading the Thingy 52 euler angle characteristic provided by the motion sensors. How is the euler angle calculated by the Thingy? Does it use raw accelerometer or gyroscope...
I'm using SDK 15.0.0 with the nRF52840 and try to sleep without SoftDevice.
The function sys_sleep_request_ms(uint32_t sleep_time_ms) from sys_sleep.h sent me this interresting...
I'm currently working on an application for Nordic that contains a bootloader and a main application using Embedded Studio. Most of the development will be on the main application...
Hello im trying to send data to mobile application, im using the example on ble_peripheral/ble_app_uart but when i compile the folowing error apears.
inking target: _build...
While writing our nRF5 based application, we have used an app_config.h in our project. This is advised as one of the solutions for updating the configuration of the SDK in...
I am a college engineering student. I currently have the NRF51 Bluetooth beacon along with the dongle I am in need of help uploading my code to the beacon via the dongle....
I have just bought an nRF51 Dongle and want to use it like a normal USB Bluetooth Adapter for my Windows 8.1. I have read the Getting Started Documentation, but there are...
I am struggling measuring time between two events. I thought to use the timer driver and the nrf_drv_timer_capture_get function and start/stop the timer with nrf_drv_timer_enable...
Dear Nordic,
I am try to implement RTC(nrf calendar implementation) in BLE example(SDK 13.0). both are working independently fine but combination of works fails RTC when...
My nrf51 SDK version is like this, nrf51 9.0 softdevice 130 chip:nrf51822_xxAArun ble_central_and_peripheral connectivity example, The nrf51 board is controlled by host MCU...
Hi All, the I/O mapping is correct as per the Ref Eval schematics. We are using a J-Link programmer to program it. The IC is not being detected in NRFgo studio. Can anybody...
Hi,
I was wondering if there is some documentation relating to pairing and bonding.
What BLE events (BLE_GAP_EVT, ???) are to be expected?
What do we need to observe...
I use ble_app_uart（sdk 14.2） + light_switch（mesh1.0.1）
Questions are as follows:
1client + 1server is ok, but in the second server there will be network failure!
log...
