Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
Only Altium can import Altium SchDoc and PcbDoc files saved in binary format. See www.orcad.com/.../OrCAD_Altium_Migration_Guide.pdf
Any possibilities of Nordic Semi saving...
I have recently been power optimising my nRF52 based application, which is a datalogger peripheral that periodically connects to a central to transfer logged readings. The...
The product description says the nRF2460 has "Support for external PA". Since this chip does not present separate TX and RX RF terminals, and no apparent TDD output logic...
Hi all,
My goal is to use all the advertising data for beaconing, and also be connectable with the NUS service.
In order to save space for the beacon data I would like...
I have a nRF24LU1 USB device that I want to configure to make communicate with a nRF24L01 device on an Arduino Uno. I tried to install nRF Go Studio and J-Link Segger driver...
Can anyone tell me whether it's possible, within the SDK (or otherwise!) to create a grouping of GPIO pins? Essentially, a design change means that we want to combine what...
Does anyone happen to have 3D models of the PCA10040 and PCA10056? I found the Altium files, but, being an Eagle user (and not having an Altium license), I was wondering if...
Hello,
I'm using nRF52 SDK12.2 "ble_app_uart_c" project as a "Central", and the target device is the "Peripheral."
Test Steps:
Using putty sending message(with...
How can i initialise all four channel of pwm1 using pwm library.
i need to initialise one channel for one purpose and other channel for different purpose.
whenever i am...
Hi,
I just tried the example from
github.com/.../nrf52-mpu-easydma-using-gpiote-and-registers
And they are working like a charm. Now I want to change the example...
In the on_ble_evt(ble_evt_t*) function from the ble_app_template, I added a case of 'BLE_GATTS_EVT_WRITE'. In it has the following code:
case BLE_GATTS_EVT_WRITE:
{ ...
I have a hard time figuring out what some of the constants in nrf_mesh_config_node_app.h for my Bluetooth Mesh application should be set as.
Instead of writing a question...
Hello,
I'm working with ANT+ hrm profile and the relative Nordic's library, but I find out that there are missing pages. Infact I have only pages from 0 to 4. How can I add...
Hi,
I have taken the BLE Central Example code (ble_app_uart_c)in one nRF51822 hardware and in the other nRF51822 hardware, I have taken the BLE Peripheral Example(ble_app_uart...
