We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi, I am using NRF connect sdk 2.6.1 and I am wondering what is the best way to run crypto operations when using TFM profile type minimal and building for nrf9160_ns. TFM_PROFILE_TYPE_NOT_SET...
I want to measure the current consumption on the DK with an Amperemeter. For that i have this setup:
Please excuse my terrible drawing skills. Im basically powering...
I am using NRF52810 as a beacon tag.
I want to apply AOA technology to this tag, is it possible?
I'm confused because the nrf52810 says it supports BLE 5.2.
Hi,
I'm experiencing memory constraints while using the nRF52811 with the SoftDevice S112, as it takes up a significant portion of the available memory. Is there a lightweight...
Hi,
We developed an application on the nRF52833 and are now porting it to the nRF54L15. As part of this process, I'm integrating an external RTC via I2C on the nRF54L15DK...
After purchasing the PPK2, I connected the Fluke287 and PPK2 Ampere meter in series to check whether the measured values matched the Fluke equipment.
The Fluke287 consistently...
Hi
I have run nrf5340 WiFi shell project in ncs2.9.0, everything ok if use Logging UART0 for cmmands(wifi scan/wifi status/ wifi connect.....etc)
now I need to use...
Hello all,
I have slightly modified the coap_client sample from the SDK such that the main function is being called on certain actions from another program. I'm getting...
I use the gpio8 interrupt to detect whether the SD card is inserted. When a falling edge is generated, it means that the SD card is inserted. But I found that sometimes, the...
So I have been doing a project on nrf52840dk, So I have built a custom bootloader for it as well, I have been trying to add the custom bootloader with the code in my nrf52840dongle...
Hello,
I have a question about the NRF SDK fundamental lesson 8 exercise 1. In the code below get_access and release_access are executed in different threads. The semaphore...
Im trying to rotate my st7789v 240x240 display with LVGL commands. Im using nRF5340.
My .dts
My code:
But this dont make any change on my rotation.
Someone...
Hi!
Is there samples for specifically make nrf54L15 show up as 2 mics for stereo audio source through bluetooth? My project require lot of development with mics and I...
Hello.
I am testing UART connectivity using the nRF54L15DK.
After assigning pins to TX and RX, there were combinations that worked fine and combinations that didn't. There...
