But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello, I'm flash download nrf52840 use st-link.
my softdevice version is s140, nrf5 sdk version is 13.0.0.
I want to flash download project, But I have an error.
...
Hello all Thank you for the many helpful posts I have encountered on this forum while continuing to discover the nRF5 SDK.
I have been trying out different examples for...
Hello,
We are working on one project in which we are planning to place PCBA with BLE module inside metal enclose.
Does it affect broadcasting range and communication...
I am using the nRF52840 (with SDKv17.0.0 + s140_7.0.1) and made a custom FW based on the ble_app_hrs example. My HW has a 64MB NOR flash memory chip and eventually I want...
The single button in the Dongle does not generate any events. I have made all the relevant changes for the preprocessor for the usage with Dongle. Kindly let me know what...
Hi there,
I am an experienced Electronics Design Engineer. In the past 5 years, however, I have only dealt with on-board systems (hardware) such as power supplies, analogue...
Hi,
I am curious as to whether one should use the nRF Connect SDK or "vanilla" Zephyr when developing let's say a BLE application that uses multiple peripherals on the...
Hi!
I'm using the download_client to fetch one file from time to time. The app is basically a clone of the sample app, just put in a function.
The problem is that if I...
Hi,
I've been developing software that uses pc-ble-driver and a PCA10040 devkit to act as a central. My software is based off the heart rate v5 example written in C, and...
Hi,
We have been working with a Zigbee coordinator based on nRF52840 with nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b, Softdevice and FreeRTOS.
We are tring to integrate...
Hello Community,
So I am building a RF system from scratch based on the nRF24l01P transceiver with a PA/LNA, using a balun for impedance matching and a band filter for filtering...
Hi All!
Hope you all are doing well ! . I am new to nrf52833. My requirement is test the range test with CODED PHY @125kbps /S=8 .
For this i tested the example "ble_app_att_mtu_throughput...
Hello.
After performing a secure DFU download, the first attempt to open a secure NUS connection fails with an NRF_ERROR_INVALID_PARAM error. After resetting the device...
I just received the nRFgo Starter Kit and am trying to follow the Starter Guide. The first step is to register the product on the Nordics MyPage (which has been combined to...
Hi, what would be the status of VDD_PA when CSN is high (Power Down mode)? Will it be LOW or Floating/High Impedance?
I know VDD_PA changes to high (1.8 V) or low based...
