Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hi team,
I am working with the nRF5340 PDK v0.8.0 and I am trying to request the additional voltage for the VREGRADIO to support the additional 3 dB TX power on the RADIO...
i have a project with Nrf24, i'm using NRF24L01 + PA LNA 2.4Ghz with athena, to get 1000m -2000m range.
But i saw on nordic website that nrf24 not for new design, we have...
I have seen a few references to SoftDevice in the 6.x series not being able to transmit at 500kbps in these forums, but I can't find anything in the docs to reference. Can...
Hi, I am using nrf52832 dev-kit. I use P0.23 or P0.24 as an input pin. I am trying use this pin to read data from other device. When I use this pin like button, it can detect...
Hello,
I would like to get some input on general framework options for development.
I am starting by strictly following the SDK framework, trying to use its drivers, translations...
Hi,
Sorry for putting so many questions in to single thread :)
----
I am looking for information on what all images been integrated to zephyr/merged.hex, can you point...
Hello!
I'm currently implementing Modbus RTU into my nRF52832 to enable the CPU to communicate with other Modbus RTU capable devices.
When communicating via Modbus...
Hi, I am relatively new with ble and nordic development. I am working with the nus service for communicating but now i also want to have ota firmware update. I am trying to...
When running the light_switch provisioner example, the application fails to the error handler when calling app_default_models_bind_setup, in access_model_application_bind...
Hi,
we are developing a device with 2 µC one being the nRF52832 for BLE connectivity. We want to do DFU via BLE with our own protocol. From what I've read, in this case...
For a customer I am developing a Zigbee coordinator / Gateway with the nRF52840. As hardware I am using the nRF52840 Preview Development Kit. As software basis I use the ...
Hello, a couple of get-me-pointed-in-the-right-direction questions, if you don't mind.
I plan on creating a system with an accelerometer that talks SPI to my Nordic nRF52833...
Hi!
I read that your Thread stack uses a different 802.15.4 implementation than the MAC driver. Is it possible to intercept special broadcast data packets e.g. from energy...
Hi!
I started to modify the ble_app_blinky example. I need to increase ATT_MTU, so I modified NRF_SDH_BLE_GATT_MAX_MTU_SIZE. For this, I needed to increase the RAM of the...
Hello,
I'm using Mesh SDk4.0.0 and SD v7.0.1. I have tested the light switch client and server examples.
Now I want to add some more models for additional functionality...
