Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
Hi there,
I'm struggling to get a DFU over serial done. I'm using a nRF52840-DK (PCA10056), the nRF-SDK 15.0 and nrfutil 3.5.0.
I
- genereated the key pair,
-...
We have a product with a microphone with PDM output that uses the nrf9160. The nrf9160 does have a PDM hardware unit that looks well suited to read it out. But currently there...
Hi Community Members,
I have a nRF51822 SoC custom board on which i have successfully tried flashing the executable file using openocd commands over Linux environment...
After the rewrite of persistent storage in SDK For Mesh v4.0.0 the code no longer does any basic sanity checks on the data read back from the flash.
The code below is from...
Hi
I am evaluating the serial_lte_modem sample with pc as client but failed, could you share the cmd format for gps start function?
here is the log after I issued the...
Hi guys, I'm facing the next problem:
I am using the Android BLE Library and Android-nRF-Mesh libraries. I connect my Android application to 8 nodes. One of those nodes...
To perform dfu using nrfutil, we need to bring wpantund service down in order to provide serial port to nrfutil. That restrict me to communicate with end nodes. Can you please...
Hi Nordic people,
According to my knowledge SPI can not verify the bits whether it is properly sending or not(like ack),speed wise is SPI ok,And in nordic nRF52840 have...
Hi!
I'm trying to use the LIS2DH12 driver on SDK 16.0.0 in SES. I've managed to read the correct value of who am i register. I'm trying to configure the sensor using LIS2DH12_DATA_CFG...
I have set up 2 nrf52 dev kits: one central and one peripheral. The peripheral side hits the PM_EVT_CONN_SEC_FAILED event about 30 seconds after the connection was established...
I'm trying every permutation.
Pressing IF BOOT/RESET button along with BUTTON 4 and powering off and on the board ... then letting the buttons go
There is a reset...
Hello,
it would seem that the Spi Slave example provided with the SDK 12.3.0 does not work correctly for the nRF51DK. Setup:
Master SPI : STM30G070CB Slave SPI : nF51DK...
Good day,
I have a problem with a custom board I have designed. It does not advertise the BLE device when programmed. I am testing with the simple ble_blinky and the nrf_connect...
I have nrf52840 development boards, when I ran DFU example (from NRF SDK for thread and zigbee v4.0.0) on autocommissioning true on 2 boards and was able to run it successfully...
Hi,
Is there any way to disconnect the NRF Toolbox connection through code. I tried to do the same but once ble turns back on its connecting back to NRF toolbox.
