I want to change data bytes in the advertisement packet. In ACI_DEVICE_STANDBY I put: lib_aci_open_adv_pipe(1);
In ACI_EVT_CMD_RSP: I get feedback that command 1B (I assume...
first,PCA10005 can't load sofeware hex that after s110 7.0.0 hex(include 7.0.0),and gostudio note that the given hex file can not open successfully.
second,the PCA10005...
Hello! I'm using sdk8 and s110. I want my peripheral device to send data to the central. I doing following steps:
1. initialize service:
void services_init(void)
{...
I am glad that I have successfully used the library from www.libstock.com/.../nordic-semi-nrf24l01-example in a pair of PIC18F45k50 devices. One is acting as a Tx and another...
Hello.
I have had a search but can not find anything so sorry if this has been covered before.
Our company has developed a consumer product using the nRF51822-QFAA-R7...
Hi every one !
I am trying to get working a code that it was working "Ok" 2 years ago.
Currently, I cannot get communication between both breakout boards.
To simplify...
Hi everyone,
I am desing a low power BLE application using the nRF52840.
How do I restart the advertising after the APP_ADV_DURATION has been expired?
Thanks in advance...
Hi,
We developed a medical device based on the nRF9160 chip and we would like to do the EMC test for qualification. Does Nordic provide any examples or support for the firmware...
Hi Team,
I have flashed the given serial LTE Modem hex file(attached) into dev kit nRF9160 and tested TCP server mode.
I am facing issue with AT command: AT#XBIND=3442...
Hi,
I´m using nrf52833 on customized board with a sensor on it. I would like to send the data, collected from sensor ober ble to nrf connect app. I print the collected...
Hi community !
i'm working on nRF52840 DK. We'll put SoC into a device where we couldn't have access with a cable. So my questions are :
1) Does DFU example use OTA to...
Hi,
I have to use current time service and one other customized service in my project.I am able to advertise only one service i.e customized one.can you please let me know...
Hi,
I am working on the nrf52840 DK using "nRF5_SDK_16.0.0".
I tested out the example code for USBD Audio in "examples\peripheral\usbd_audio".
If I use the default values...
Hello. I evaluated the effect of temperature and humidity on BLE connection stability. I thought that the effect of humidity was higher than that of temperature, but the effect...
I'm trying to rate nrf52832 now. I'm using Keil uVision5 as my development environment.
I have written softdevice s132_nrf52_7.0.1 for the target.
I'm trying to set the...
Dear Sirs:
I use 52832, and there is 512KB internal flash.
So, I am wondering if I could have my own flash partition as below.
- Bootloader (w/ capability of firmware...
Hey all,
I've been bringing up the nRF9160 Feather and noticed some curious issues with adding an external partition when MCUboot is enabled.
I first tested the external...
We are developing a board based on nRF52840. One of the pins we would like to use as GPIO is P1.09. It is configured as GPIO (the same configuration as P0.12), but the output...
Hi,
I compiled and flashed my nrf52840-DK with "examples/peripheral/usbd_audio" and I noticed a few things:
Under Linux (Ubuntu 18.04) the microphone isn't listed. ...
We were use secure ble DFU and it work fine, recently we added serial DFU code with BLE DFU. Tested serial DFU with nrfutil and it also works. but problem in serial DFU is...
I try to invert the Signal on a PIN of the PWM module 0. It sould give out the inverted Signal of another PIN from the same PWM module.
I tried it like the code below...
