Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
I'm having a advertising device and then I want to stop advertising and prevent BLE connection from device that would have received the advertisement. It seems to work by...
Dear Team,
I am trying to add my Thingy 91 to nRF cloud, but I receive the following error :"There was an error adding your device: No device found with id 'nrf-xxxxx'....
Hi Nordics
https://devzone.nordicsemi.com/f/nordic-q-a/22595/can-not-received-ble_gap_evt_timeout-event-when-connect-timeout/88877#88877
Referring to the above post, I...
Dear,
I am trying to test BLE on the THINGY:91.
Follow the Q&A for "Introduction to Nordic THINGY:91" webinar, Q12 of @ Petter Myhre
I tried with Zephyr HCI UART example...
Hi,
I'm trying to debug my bootloader (I2C specifically) using Ozone. However the CPU only seems to halt when trying to debug the bootloader.
Also setting breakpoints...
I am using proprietary radio between 2 nrf51 devices, by copying from an example see code below.
That works but now I want to have more pairs of devices and I need to have...
Hello,
I have some custom hardware that uses both BLE 4.0 and BLE 5. I am looking for information on if it is possible to use a nRF52840 Dongle to connect to multiple peripheral...
Hi ! I am trying to design a custom board for nRF52840. I used the nRF52840 dongle's HW files in Altium to create a new board. Unfortunately the Altium project does not include...
I am trying to make the timer example works under the BLE blinky example. I have copy the code and enable the defines in sdk_config,from one project to the other but timer...
Hi i want to send a string using uart over bluetooth. For a try i compile ble_app_uart and flash it to my dk but i can not see the message on the terminal neither in Putty...
Hello everyone,
I am using nrf52832 module with SDK v14.2 and SD v5.0.0 for my development.
Recently, i started facing the below issue:
Once i try to pair the module...
Hi Great QA team:
Our client has made their product in MP stage but found out that some of the ICs with FDS Bug (Base on SDK 15.2):
REF: FDS - data corruption https:/...
Hello,
Quick question.. we are working on a board and running very low on GPIO pins. It would be helpful to remove the low-frequency (32k) XTAL, to recover those pins. The...
Dear,
I am testing with thing91
todo: read and send the temperature to my webserver in each 15mn
using: thingy91, LTE_M
sample1: in the fridge (4C)
sample2: in...
