It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
I want to change data bytes in the advertisement packet. In ACI_DEVICE_STANDBY I put: lib_aci_open_adv_pipe(1);
In ACI_EVT_CMD_RSP: I get feedback that command 1B (I assume...
first,PCA10005 can't load sofeware hex that after s110 7.0.0 hex(include 7.0.0),and gostudio note that the given hex file can not open successfully.
second,the PCA10005...
Hello! I'm using sdk8 and s110. I want my peripheral device to send data to the central. I doing following steps:
1. initialize service:
void services_init(void)
{...
I am glad that I have successfully used the library from www.libstock.com/.../nordic-semi-nrf24l01-example in a pair of PIC18F45k50 devices. One is acting as a Tx and another...
I am using SES V4.18 with SDK 15.3.0.
In sdk_config.h, I have set APP_VERSION_MAJOR and APP_VERSION_MINOR etc...
Is it possible to add these numbers to the output file...
I recently added Mesh DFU support to a project that I'm working on but it's extremely slow. It will take at least 1 hour to update the network under ideal conditions but I...
Hi,
My stack is
s112
SDK 15.3
Segger
nrfConnect
nrf52832 DK
Power profiler kit connected via USB to my MAC to get the traces to run.
CR2032 batter removed...
Hello
I cannot load the Radio Test code onto the Nordic NRF52 devkit. I'm using SDK15.3 and the project located at C:\nRF5_SDK_15.3.0\examples\peripheral\radio_test.
The...
Hello,
I noticed this weird bug that coincides with the SD card not initializing using the FATfs.
Basically, I have the SCLK pin of the NRF52DK connected to a breadboard...
Hi All: I am using NRF51802 ,SDK is 12.30 version, and softdevice is s130 2.0.1 version. using keil MDK 5.23 Version. And download the softdevice using nrfgostudio and keil...
Hello,
I have a nordic nrf52840 on board, with another MCU (Cortex-M4) on board. Both chips are connected over UART.
I want to use the Cortex chip to perform firmware...
Hi.
We have a strange issue we are seeing with a nRF52840 where scanning fails, but it is very rare.
Setup - nRF52840 is a central device, and there are 20 x nRF52832...
Hello Nordic!
I'm developing with s340, nrf52840, and sdk 15.3.0
My device is a peripheral and the phone is master in ble.
I listen to my coworker who is developing...
Hi, I'm trying to set P0.20 pin as MISO of my spi master to communicate with ADXL372 accelerometer sensor, but when the miso is disconnected the signal received matches with...
Hello.
I want to develop a custom bootloader able to update firmware version Over-The-Air (BLE)
I'm using a custom Dev Board based on nRF52832 with and nRF SDK V15.0....
I am developing device that uses NRF52 and GSM modem. Sometimes when connecting to bonded device connection fails and phone pop-up appear and ask for pairing. GSM antenna...
Hello,
we are using nRF Connect for Desktop with a nRF52840 USB dongle for our testing purposes. I found no feature for “Request MTU” (ATT MTU exchange), like it is available...
Hello,
I am using nrf52832 board, having SDK 15.3.0, in Segger studio IDE, on windows10.
I am using bluebee board in which mdbt42q chip is used.I am trying to toggle gpio...
Hi
We have a lot of customers asking for full extended adverts features as per the latest spec in terms of all types of adverts and also other PHYs
Apparently other BLE...
