But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi I use nrf-ble-driver ver.4.1.1 with PCA10031 dongle (nRF51844 chip on board) and "connectivity_4.1.1_1m_with_s130_2.0.1.hex" firmware for that dongle. in this case ATT_MTU...
Hello to everyone. I´m starting to work with Mesh configuration in nRF52 SDK. I was testing the "light_switch" example as client and server in Mesh v3.10, provisioning with...
Hi!
I am trying to run a customized project which is based on the project in the following directory- "nRF5_SDK_14.0.0_3bcc1f7\examples\ble_central_and_peripheral\experimental...
Hi, I connect the HDC2080 with nrf 52832. but I cant read anything from the terminal. What It's showing is just
[ <info> app: TWI sensor example]
and I connect SDA --...
I'm working on porting a project plus bootloader from SDK 12.2 to 15.3. I have the application working fine, but the bootloader is having some issues. Most of the searches...
Hello there,
i am using the nrf52dk and want to program a selfmade breakout board which includes the BMD-340-ar Bluetooth module from rigado.
I use Segger Embedded Studio...
Hi,
I am trying to extablish TWI communication between 2 nRF52832 devices. One should be master and other slave.
For TWI initialization in nRF52 master, I have below source...
Hello!
I'm new to the nRF52 and to ANT, so I'm in the process of running through some of the example code. I've been able to successfully run blinky example. However, I...
I have an nrRF52832 central connecting to 16 (nordic-based) peripherals. We allow up to 20 connections on this design, but only 16 are currently connected during this test...
Hello,
I'm working on a project and we're using the nRF2840 to get data from a BNO080 IMU.
Someone already wrote arduino code which works. How does one change the sample...
Hi, i'm working a BLE gateway with NRF52DK and S132 by using the demo example central uart.
The peripheral equipement advertise manufacturer data like this:
0x0001 during...
Hi there,
I am new to the Bluetooth mesh and I am learning about it. I have some questions about Bluetooth mesh. I hope you will help me with this.
Please pardon me...
Hi
I am trying to implement the communication between nrf52832 dk and nodemcu esp8266 over i2c.
My i2c code in nodemcu is working fine as I had tested the communication...
Using latest download of nrf Command Line Tools and a J-link Plus unit with Tag-Connect interface. Power on, all connections seem good. Trying to upload a .hex file through...
