I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
Hello,
I'm usign nRF52832 IC and SDK5. I want to awake the sleeping MCU by NFC and pair with BLE. In short Pairing device address should be transfer via NFC. There will...
Hi all
i am using SDK15, nrf52832 dev kit and s132 version 5
I followed the below steps:
1)Flash the softdevice
2)Update the generated dfu_public_key in secure_bootloader_dfu...
I am developing a firmware and connected a spi LCD to nRF52840, but I got the max speed only 8 MHZ, in Datasheet is 32 MHZ max.
Which speed of the SPI master is max ? (I...
I'm getting a disconnect reason of 0x3D / BLE_HCI_CONN_TERMINATED_DUE_TO_MIC_FAILURE during a connection attempt. It does not happen for all my phones except one. It appears...
Hello Everyone,
I am a beginner and working on nRF52832 DK using SDK v15 and using keil mdk armv5.25 as a compiler. Currently I am trying to modify an example in the SDK...
Hi,
Quick question: I read in this article on the section "A tough world of lighting controls" it states the following: "Let's say that five messages are spaced 20 ms apart...
Hello everyone ,
We are able to read out ADC values(if i connect battery positive externally on ADC pins). i wanted to know if there is internal connection provided to any...
Hello,
Testing your nRF Connect with a BLE Thermometer. I was able to connect and read data.
Can you help me with one question I have ?
This is part of the log file...
Where to start? Is it possible?
I need to send data between the two chips using 802.15.4.
There is no need to form a network.
I was looking at the Wireless Uart example...
Hello all,
We want to run the example TCP-Client example from IOT SDK.
how should we proceed for the same ?
Which softdevice must we use ?
Thanks and Regards ...
Hi,
My setup:
* nRF52 DK
* nRF5_SDK_15.0.0_a53641a
* s132_nrf52_6.0.0
* SES V3.34b 64-bit.
I am struggling to properly use FDS module. I am using multiperipheral...
Hi Support Team,
By testing SDK15.0.0/Serial DFU, I find that if we use non-default baud rate(115200), such as 9600 or 38400, we have to assign a non-zero value to -prn...
Hi everyone,
I have 2 boards that I've been using for testing. One is the NRF52 DK with the nrf52832 and the other is a simple custom board i made with an nrf52810.
I...
Hi all,
I'm currently making Mbed OS 5 able to work with the NRF51 with DFU enabled. It seems Mbed OS 5 currently has no support for a Nordic bootloader for the NRF51. Mbed...
