We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi,I made a 52840 board ,it's p0.18 hanging, without connecting a 10k pull-up resistor and a 100nf capacitor to ground. I connected 3v3, GND, SWDIO, and SWDCLK from the 52DK...
NRF54L15 NCS 3.02
I have to change my BLE advertising from Legacy to Extended. Looking at the Zephyr example "advertiser" which compiles & runs fine, but I notice that behaviour...
Hi,
I am currently trying to connect a nrf52811 as an companion to an ESP32 user UART.
I am using the interrupt driven UART implementation as kind of the last resort....
How can I set a custom interval for *extended* advertising?
I'm currently calling bt_le_ext_adv_start ( struct bt_le_ext_adv * adv , const struct bt_le_ext_adv_start_param...
~~~~~~~~~~Environment ~~~~~~~~~~ nrf54L15 + NCS 3.1.1 + VSCode + Win11 ~~~~~~~Reproduction Steps~~~~~~~~~ 1. without pm_statics.yml, with following configs (see attachment...
Dear Team,
I am experiencing a weird issue with the firmware on my custom EV board with NRF54L15.
My firmware is using MCUBoot and partition manager (I use a separate...
Dear Team,
I need to switch LXFO to internal RC for MCUBoot, however, I am experiencing troubles configuring it on NCS 3.0.1 (NRF54L15).
If I just add my RC settings to...
Hi,
Our project requires an unusual combination of running BLE, Gazell, and raw radio packets for time sync simultaneously.
Time sync and BLE are infrequent activities...
Issue:
I would like to bring to your attention that I am getting an error when running the 'list command using the nrfcredstore cli utility, while trying to retrieve the...
Hi,
I've run into an issue when doing some compatibility testing between our client's legacy device (802.15.4 transmitter) and the current device in development (802.15...
In the introduction to the bare metal SDK option for the nrf54L:
https://www.youtube.com/watch?app=desktop&v=31znTI-hnCQ
it mentions at around 58:00 that single bank...
I am using nrf connect SDK toolchain version 3.1.1 and nrf connect sdk version 3.1.1 , By default I don't have zigbee related samples/examples and also zboss stack library...
The original question was: "The nRF52840 PS mentions, that this chip contains an ETM but it does not mention the implemented version."
Researching the topic more, I found...
Hello Team,
We have noticed a very weird issue with the nRF5340 Audio DK. After flashing the audio application code given by nordic, everything works perfectly fine. No...
