But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello,
I've been trying to modify the v2.4.0 Serial LTE Modem application sample for my nRF-9160 custom board, in order for it to communicate with our external MCU through...
Hello,
I'm currently running into issues when using the Logging Interface with USB CDC ACM. I tried to combine the cdc_acm sample and the console sample into one application...
Hello,
I measured the DC resistance between the RF output pin and ground pin and got around ~3-4 Ohm with digital voltage meter. This seems low. Am I missing something?...
Hi,
I have two nRF52833 DKs and both of them has connected to nRF21540 EK. I set the transmitter sending out 244 bytes data without stopping and measure it's current. The...
Hi there,
I want to debugging my beacon project card which designed with NRF52832 MCU
I have NRF54L15 PDK Development Kit and it has debugger on the kit.
How can I debug...
Reporting this here as the project GitHub asked that bugs be reported via DevZone.
The latest Power Profiler v4.2.0 has introduced an annoying issue - when running the Power...
I'm studying the nRF Connect SDK Fundamentals course and working with the NRF54L15 PDK. In Lesson 1, I'm trying to turn on LED0. I can build and flash, but the LED won’t turn...
I am using the s120 soft device v2.2.1 as a center communicating with a peer using a s110 soft device.
The peer is a black box an all I have is the documented protocol.
...
The nRF Kconfig extension ( https://marketplace.visualstudio.com/items?itemName=nordic-semiconductor.nrf-kconfig ) does not recognise some of the Zephyr kconfig extensions...
We are currently developing an ECG sensor patch that will operate over a cellular network, and we are considering using the nRF9151 for its LTE-M/NB-IoT capabilities. Since...
I'm interested in determining the current coverage enhancement behavior of a device, and I'm noticing a discrepancy between the AT+CEINFO and AT%CONEVAL results. Specifically...
as my last post issue nrf desktop in ncs SDK cant work when onnect to cmac os - Nordic Q&A - Nordic DevZone - Nordic DevZone .the ncs desktop cant work in mac os in nrf52840...
We are currently mass producing nrf52833. However, there is a problem with BLE communication. The defective product does not appear in the BLE search list at all. The failure...
Hi,
I'm working with UART with DMA(UARTE) on nRF52840. UART does not have HW flow control, just RX-TX.
I'm confused with DMA part. Is DMA circular or I have to reset it...
