But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello ,
I have NRF thigy 91 and nrf9160 DK board and have flashed asset tracking hex file in both the devices .
But the thingy91 is not able to connect to nrfCloud but...
Hi,
Some of purpose we want to terminate current connection and rejoin to exit PAN.
I use zdo_mgmt_leave_req to request for leave. However , at callback , the status...
Hi,
I use FDS to store some data.
After creating the file, update the data using fds_record_update().
When the update is completed, FDS_EVT_UPDATE occurs in FDS_Event_handler...
Hi,
I read data from FDS and output it to nRF USB. The output is implemented by
app_usbd_cdc_acm_write (&m_app_cdc_acm, m_tx_buffer, (sizeof(m_tx_buffer));
But I only...
I've been going through the nRF Mesh SDK and want to integrate it with my Zephyr project.. Reading through the various blog posts and documentation, it seems that the Mesh...
Hello
I'm learning the nRF5340 using the purchased nRF5340DK. After completion the beginner's tutorial advanced to the Getting Started tutorial on BLE custom service for...
I am looking at the example of the HRS collector (Central) of the SDK also called ble_app_hrs_c.
In the file nrf_ble_scan.c in the function nrf_ble_scan_on_adv_report we...
Hi,
I am using ble_app_beacon with Softdevice S140 with SDK 17.02 for nrf52840.
In the example code I want to set beaconing to only one channel (channel 39) and be able...
Hi Nordic Team,
when discovery custom 128bits uuid service, I have high probability get BLE_GATT_STATUS_ATTERR_ATTRIBUTE_NOT_FOUND, but sometimes I get BLE_GATT_STATUS_SUCCESS...
Hello,
I am upgrading my project from SDK 15.0 to SDK 17.0 and I get this message.
Please see my project's comfiguration file:
debug_additional_load_file="../SDK_17...
Hi, all
I'm trying to i2c(twi) in low power..
In this case, I want to generate an interrupt through the i2c read function " read_touch_data " (under code).
Where...
Hello team,
We have a sensor design based on nRF52840 and currently we have configured it in the normal voltage mode DC/DC REG1 enabled. It is a battery operated design...
hi,
I am using nrf5340 dk board and nrf connect sdk. i want to encrypt the data and decrypt the data in application core. I have seen cryptcell 312 for cryptohraphic algorithms...
Hi,
I am currently working with the nrf52840, ble_app_uart example under the ble_peripheral folder. Using the tutorial below:
https://devzone.nordicsemi.com/nordic/short...
