first,PCA10005 can't load sofeware hex that after s110 7.0.0 hex(include 7.0.0),and gostudio note that the given hex file can not open successfully.
second,the PCA10005...
Hello! I'm using sdk8 and s110. I want my peripheral device to send data to the central. I doing following steps:
1. initialize service:
void services_init(void)
{...
I am glad that I have successfully used the library from www.libstock.com/.../nordic-semi-nrf24l01-example in a pair of PIC18F45k50 devices. One is acting as a Tx and another...
Hello.
I have had a search but can not find anything so sorry if this has been covered before.
Our company has developed a consumer product using the nRF51822-QFAA-R7...
Hi every one !
I am trying to get working a code that it was working "Ok" 2 years ago.
Currently, I cannot get communication between both breakout boards.
To simplify...
I'm trying to solve an intermittent problem when using the nRF51422 UART with CMSIS-RTOS (RTX) and MDK Networking library (V6.2) (TCP/IP stack).
My questions relate to...
Hi All,
I cannot get the NRF_LOG messages via RTT to the debug terminal in SES or RTT Viewer.
My setup: HW: PCA10040 SDK: 17.0.2 Project: nRF5_SDK_17.0.2_d674dde...
Hi,
I followed all the steps to get NCS up and running with SEGGER Embedded Studio. However, when I try to open an example, I get this error:
Including boilerplate ...
Hi all,
I am currently working with nRF52832 boards, and I am trying to save some values in my flash memory. I have already created a code for this purpose and I am able...
Hi, I'm currently trying to understand multi-Link and Immediate Alert Server Application (ias) examples in SDK 17.
While I'm analyzing them, I got some questions:
Q1)...
Hi,
I am working on the nRF52832 ,why i can't able to set the low 7.5 ms interval . I am getting the error at ble_advertising_start . Do I want to change anything else?...
We are preparing our nRF52 product for the unintentional radiator test. Currently, the SoftDevice is enabled and we have the low power mode disabled with the following changes...
Hi,
Looking for some guidance on how to use the 'cryptographically secure random number generator' in a Zephyr/nRF Connect SDK application on an 52840
Is this a supported...
Hi sometimes it happen with my nrf52832 based device. The common way I am programming firmware during development is next:
nrfjprog --program fw.hex --sectorerase --verify...
Hi,
I am working on the nRF52832 ,If i want my data to be transmit every 7.5ms then what should I set the minimum connection interval and maximum connection interval ? please...
Regarding that the nrf52811 is able to use direction finding, there is any example for configure a tag with the nrf52811 to be located? Did nordic finally release any AoA...
Hello,
Sorry if it will be long. thanks for the help.
Using nrf9160 dk. The first thing I want to ask is about is the pins. I want to make sure I am using the correct...
Hi
I am currently using nrf52840dk with zephyr, and SPI used to work fine.
Now, as a slave, the kit only reads the data read while MISO is high (this might be what's supposed...
Hi, I am trying to create and FOTA upgradable application on the nrf52811 SoC. I have managed to do the same for nrf52832, but when I repeated the process for nrf52811 it...
Is it possible to use multiple NUS client with NCS ?
One of the problem i see is that nus client callback (bt_nus_client_cb) don't have information about the connection...
Hi,
My application needs to enter DFU mode based on a command from another device connected via SPI.
I see that I could use the following two statements once the application...
