But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
1. I tested the following AT instruction on ncs v1.3, returned OK, but did not return the subscription message, need to modify where to return the subscription message did...
We are using I2C bus for communication with a RTC and Accelerometer. But sometimes the I2C get struck in i2c_write. It does not happens always it may happen randomly. We are...
Hi,
I just spent several hours trying to figure out why, using a nRF52 dev kit w/ SDK13 + S132 on both central/client and peripheral/server side, sd_ble_gattc_read() was...
Dear Support,
I have a question about the IPv6 networking with OpenThread. I do have an mesh network with about 50 nodes (PCA10059) and implemented CoAP servers and clients...
I just downloaded SEGGER Embedded Studio (ARM V4.52c) and plugged in my rather old PCA10040. It offered to upgrade the driver, which I accepted. Now, when I click "Connect...
Hi,
Just installed nRF Connect v3.4.1 on a macOS Catalina and get the following error message when starting any of the apps:
I've tried both reinstalling and downgrading...
Hi,
I'm making a peripheral device that needs to minimise battery usage.
My device is essentially a beacon but it allows temporary connections to send a stream of data...
Hello,
I have purchased a new nrf52832 DK board for development. I tried to run some examples like ble_app_blinky which are working properly. But when I tried examples such...
Dear All:
Our team are ready to develop a project with multicentral and multiperipheral
The project topology image lists as follow:
I want to ask how many ram it will...
I know this sounds a crazy question but is it possible to flash a custom nRF52832 board with the same firmware that is shipped with the dev kit and create a mass storage out...
Hello,
I am looking to run the ble_app_uart example from the SDK v17 in nRF only mode on the nRF52840 DK. When running the application as is on nRF only mode, it fails during...
I bought nRF51 dongle from mouser.com. I wanted to put nRF sniffer firmware on it using the guide on the web site. I tried using nRF connect programmer but it can not talk...
Dear all,
I've been struggling with SECUREAPPROTECT register in UICR Flash area on a nRF9160 DK.
I would like to restrict and protect Secure code loaded in Secure mapped...
Hi, we have a custom board using the nrf9160, running modem firmware 1.1, and using the nrf9160_gps driver.
Sometimes we see messages like this:
Tracking: 8 Using: 0...
