Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
I am trying to set up the LPS22HB sensor with an nRF52840. I am starting with the twi_sensor example(SDK16->examples->peripherals->twi_sensor) and adding the lps22hb example...
We have added custom HID firmware and are able to discover it on the Android Bluetooth Settings app. iOS fails to show the Bluetooth device on iOS Bluetooth Settings app....
Hi,
My task is..
Device will advertise for 20 seconds if there is no connection then it will go to sleep mode for 40 seconds. After 40 seconds it will wake up from sleep...
I have the nRF9160DK 0.8.3 which appears to align with the suggested schematic in "Objective Product Specification v0.7.1" I downloaded the hardware files form the Getting...
Hi,
To turn on and turn off the LED nrf SDK is using following code in sdk12.1.
#define LEDS_OFF(leds_mask) do { NRF_GPIO->OUTSET = (leds_mask) & (LEDS_MASK & LEDS_INV_MASK...
According to SIG's MESH Profile: "There is also a device key (DevKey), which is a special application key that is unique to each node, is known only to the node and a Configuration...
Hi,
I'm checking the e-sim functionnality with at_client firmware and LTE LInk Monitor. Once connectivity is proven to be successful, I can pursue my testings.
I was...
Hello!
I have questions.
I develop a central and peripheral devices at nrf52832.
I use SDK 15.3.0, s132 v6.1.1.
1.If I program Nordic's BLE peripheral sample into...
SDK ： nRF5_SDK_15.0.0_a53641a
example： nRF5_SDK_15.0.0_a53641a\examples\peripheral\twi_sensor
I didn't change anything. After build and download to the Nordic development...
Hello,
Im using pca10059 to scan for near beacons address and RSSI, but i also want to look for its battery level. (im using pca10056 to develop and debug)
I've found...
Hi.
I would like to measure the battery voltage using ADC in MCU. PCB has limited space, I consider to use the IC for this application.
The following is the LDO with...
Hello,
I am working on an IoT project using the Thingy 91 to send sensor data via Bluetooth to a remote device. Currently, I am trying to set up a simple beacon as shown...
Peripheral: SDK13.1 nRF52832
I don't want to change ConnectionParamaeter of Periperal by ConnectionUpdate request from Central. Can Periperal ignore ConnectionUpdate from...
