I am glad that I have successfully used the library from www.libstock.com/.../nordic-semi-nrf24l01-example in a pair of PIC18F45k50 devices. One is acting as a Tx and another...
Hello.
I have had a search but can not find anything so sorry if this has been covered before.
Our company has developed a consumer product using the nRF51822-QFAA-R7...
Hi every one !
I am trying to get working a code that it was working "Ok" 2 years ago.
Currently, I cannot get communication between both breakout boards.
To simplify...
I'm trying to solve an intermittent problem when using the nRF51422 UART with CMSIS-RTOS (RTX) and MDK Networking library (V6.2) (TCP/IP stack).
My questions relate to...
Hi...
When i was working in SDK v6.1.0 i have tried nrfprog.exe to merge and program bootloader, softdevice, application and bootloader_settings file as explained in devzone...
Hello All
I try to port the blinki example (with softdevice s130 2.0.1) to my Hardware with the nrf51822_xxAA.
The application will run without Softdevice.
But as soon...
Stack violation: stack pointer outside stack area.
Cause: Data bus error (PC value stacked for the exception return points to the instruction that caused the fault).Bus...
Hi,
I have PCA10000 Revision 0.9.0 nRF9160 Board with external antenna (Molex 206640)
I try to make GPS work. Here is my step:
I compiled GPS under samples ..\root\ncs...
I followed the start up procedure-
All OK, but my nRF9160DK doesn't connect to the network.
Only led3 is blinking.
I think iBasis-eSIM is not enabled in my area.
I...
Hello,
I need my timer to work at 9600 bps frequency. So accordingly my frequency is 16MHz and to get 9600 Hz I calculated the prescaler to be 10.7 ~ 11. But in the timer...
I'm using nrfutil ( https://github.com/NordicSemiconductor/pc-nrfutil/releases/tag/v6.0.0a1 ) with an nRF52840 USB Dongle to update units through BLE. The device is nRF52832...
Hi,
Nordic Part Used in Design: nRF52810
SDK version used 16.0.0.
We found for nRF52810 it supports peripheral mode as well as bootloader. I didn't find any example...
Hello:
I enabled LTE and GPS in my project and I encounterd a terrible hard fault error.
The error didn't happed once I programmed my hex file.
It work fine but hard...
Hi,
Does the zephyr stack support scanning for extended advertising packets on the nRF9160?
I tried opening the lte_ble_gateway example in ncs v.1.1.0 and adding CONFIG_BT_CTLR_ADV_EXT...
Hi,
Nordic Part Used in Design: nRF52810
SDK version used 16.0.0.
We found for nRF52810 it supports peripheral mode as well as bootloader. I didn't find any example...
I'm using SDK version 15.0.0_a53641a on nRF52840 with softdevice s140_nrf52_6.1.0_softdevice.hex.
sd_ble_gap_adv_set_configure() is returning error code 7 when I use BLE_GAP_ADV_TYPE_EXTENDED_NONCONNECTABLE_SCANNABLE_UNDIRECTED...
OVERRUN error occurs when receiving UART.
I'm using EasyDMA with UART and want to increase the EasyDMA reception size. Which settings can be used to increase the reception...
Hi,
I have NRF52833 DK and using nRF5 16 SDK on KEIL IDE.
I am trying to compile blinky example from the peripheral and it is giving me this error
Error #541: 'NordicSemiconductor...
During production we need to provision each device with some custom data that must last the life time of the device, ideally using nrfjprog. What is the best way to do this...
There are several use cases where we want a bonded peripheral to indicate the service changed characteristic to the central.
The main case is when developping and adding...
