But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
We developed our device with KEIL 5, SDK15.2 and SoftDevice 6.1.1. After we upgrade the SDK on our device from version 14 to 15, our IOS phone encountered the following...
Dears:
I'm testing the USB mass storage example: \examples\peripheral\usbd_msc with Nrf52840DK and SDK v15.3.0.
Now I have one question. When I plug in/out USB to PC or...
Hi
I am using the NRF52832 ,my code is based on the ble_app_hrs_freertos example sdk 15.0.0
I have one main task which usually run 64 time every second using the vTaskDelayUntil...
Hi I have a module that is used in a hand held instrument. It contains the nrf52832. It connects to phones for data communications. Is it possible to determine the strength...
Dear All,
I am trying to compile and run the ncs/zephyr/samples/drivers on the nrf9160_pca10090ns. For this reason, I have copy-pasted the file under the ncs/nrf/samples...
Sorry, I want to ask that if I can send Decimal(like accel x,gyro x) by the ble characteristic to the nrfConnect, when I send the information, it always becomes hexadecim...
Dear community members
I have end nodes with nrf52832 (Soft device s132) that can communicate to a central nrf52832 DK in Connection mode based on ble app uart and multiple...
hello, I'm develop use nRF52 SDK15.3 template to measure water press, and gyro value.
but in nrftoolbox app just show signed value, so i want to show signed value.
please...
Hello ,every one ,I found that the nrf Connect will disconnect it self after connecting to the device after 30 seconds, I'm using the sdk15.3.0 ble_app_template example,I...
NRF5_SDK_15.2.0
I am run my android code on android 9 and android 7. Unfortunately my android 9 is paired sometimes and not paired sometimes. especial after i tried to connect...
I am currently developing applications using nRFtoolbox. In case of ses, we are developing a template, but the application does not produce a negative value. In this case...
Hi, this is my first time using nRF52832 as a central device. (S132 6.0.0)
I set up the scan timeout parameters, it does stop scanning at the time I expect,
but strangely...
Hi,
It seems I'm running into the fairly common "solution load command failed (1)" error on a nRF42840DK board.
The console output in Segger gives me the following:
...
Hi, I am using mesh sdk 3.20 and nrf52840.
I am using 3 nodes for testing. One generic on off client and two generic on off servers.
I believe that I have managed to get...
