At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, per the question, how?
Is there certain register in the nrf514xx devices which can be called up in debug mode & used for such a purpose? By that I mean:
place...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I'm using the nRF52DK and S132. Is it possible to encrypt a link without any pairing, bonding and authentication process ? Please show me the way how to implement with the...
Hello.
I need to create multiple btle apps with support for the following network topology:
1 btle sensor node; it implements hrs
and bas services
1...
Hi All,
I need to certificate the nrf52 to Fcc. I understood that the radio test is very useful.
I try to clarify what the code permit to do, because i want to adapt it...
I must create an application for nrf5 dk with s132 v3.0.0 sd. In this application a device must implement heart rate service client, while continously trasmitting a reference...
Dear Nordic Engineer,
I need to work on nRF52, my Macbook Air has OSX Yosemite 10.10.5 - I can run "make" or "nrfjprog" only if I copied libjlinkarm.dylib into the same...
Hi
I am presently working on MPU92/65 sensor interfacing with TWI/I2C.
i am using nRF51822 EK with soft device s130_nRF51_2.0.0(id:0x0080) and nRF5 SDK v12.2.0 and keil...
using
nrfjprog --rbp all
and got a success
and using
nrfjprog --readuicr
got unavaible
but if using j-flash and read whole chip, it's able to be readback...
it...
I am trying to figure out how/if I can program the softdevice hex from keil? I know I can just use nRF studio however its annoying sometimes....I also noticed I cannot rebuild...
I'm using an nrf52dk (pca10040) to develop an mqtt subscriber application.
I'm using the IoT softdevice, with the IoT 0.9.0 sdk example for subscriber as a starting point...
Hi,
I want to know in general about the UUID that we add in to GATT files.
Basically, I want to know that there are different UUIDs for different applications heart...
Hello everyone,
I successfully implemented the static key to access a characteristic now I want the user to udpate the passkey through another characteristic (which is also...
Hello, with a little research, I now decided that this is the general but incomplete (which is why I'm asking the question) step :
Immediately look up SP register, if the...
